Miele Food Warmer EGW 2060 User Manual
Operating instructions  
Built-in Plate Warmer  
EGW 2060  
To prevent accidents and  
machine damage read  
these instructions  
before  
UV  
installation or use.  
M.-Nr. 06 405 620  
 
IMPORTANT SAFETY INSTRUCTIONS  
Technical safety  
This appliance is intended for  
Before installation make sure that  
the voltage and frequency listed on  
the data plate correspond with the  
household electrical supply. This data  
must correspond in order to avoid risk  
of damage to the appliance. If in doubt,  
consult a qualified technician.  
residential use only. Only use the  
appliance for its intended purpose.  
Improper use of the appliance can  
lead to personal injury and material  
damage. The manufacturer cannot  
be held responsible for damages  
caused by improper use of the plate  
warmer.  
The electrical safety of this  
appliance can only be guaranteed  
when continuity exists between the  
appliance and an effective grounding  
system. The grounding system must  
comply with local and national safety  
regulations. It is imperative that this  
basic safety requirement be tested by a  
qualified electrician. The manufacturer  
cannot be held responsible for the  
damages caused by an inadequate  
grounding system (e.g. electric shock).  
This appliance complies with current  
safety requirements.  
Read all instructions before installing  
or using for the first time.  
Keep these operating instructions in  
a safe place and pass them on to  
any future user.  
Do not connect the appliance to  
the electrical supply with an  
extension cord. Extension cords do not  
guarantee the required safety of the  
appliance.  
Read all operating and installation  
instructions for any other appliance  
installed in combination with the  
plate warmer.  
This appliance must only be used  
once it has been properly installed  
into cabinetry to ensure that all  
READ ALL INSTRUCTIONS!  
electrical components are protected.  
Never open the outer casing of the  
appliance.  
Tampering with electrical connections  
or components and mechanical parts is  
dangerous and may cause machine  
damage.  
3
 
 
IMPORTANT SAFETY INSTRUCTIONS  
Installation, repair and  
maintenance work should be  
performed by a Miele authorized  
Do not use the plate warmer to  
reheat, cook or keep food and  
drinks warm. The condensation from  
service technician. Work by unqualified food or drinks could lead to moisture  
persons could be dangerous and may  
void the warranty.  
damage in the appliance.  
Do not lean or sit on the warming  
drawer. This will damage the  
Before installation or service,  
disconnect the power supply to the drawer which can hold a maximum of  
work area by removing the fuse,  
"tripping" the circuit breaker or  
unplugging the unit. Pull the plug not  
the cord.  
33 lbs (15 kg).  
Do not store anything in the  
warming drawer. Forgotten items  
could melt or catch fire when the  
appliance is turned on. Flammable  
liquids and materials should never be  
stored in, above or under the plate  
warmer.  
Use  
The plate warmer interior gets very  
hot when in use and stays hot for a  
while once turned off.  
Do not use the plate warmer to  
heat the room. Due to the high  
temperatures radiated, objects left near  
the appliance could catch fire.  
Use heat-resistant pot holders  
when removing dishes. Be sure  
that they are not damp or wet. Danger  
of steam burns!  
Do not use a steam cleaner to  
clean this appliance. Steam could  
penetrate electrical components and  
cause a short circuit. Pressurized  
steam may cause permanent damage  
to the surface and to components of  
the appliance, for which the  
Pull the drawer out all the way  
when removing dishes to avoid  
touching hot drawer parts.  
Do not let children access the  
appliance or its controls. Supervise  
its use by the elderly or infirm.  
manufacturer cannot accept  
responsibility.  
4
 
Guide to the machine  
a Temperature selector  
b On/Off button  
c Sticker  
d Indicator  
e Warming drawer  
f Non-slip mat  
5
 
 
Before using the plate warmer  
^ Clean the plate warmer with a damp  
cloth and wipe dry.  
^ Heat the empty plate warmer for a  
minimum of 2 hours. Turn the  
temperature selector to "Maximum"  
(see "Selecting a temperature").  
^ Vent the room when heating the  
drawer for the first time.  
Metal components have a protective  
coating which may give off a slight odor  
the first time your new appliance is  
heated. The smell will dissipate after a  
short time and does not indicate a  
faulty connection.  
6
 
 
Using the plate warmer  
Opening and Closing  
The plate warmer is only intended  
for warming dishes.  
^ To open and close the plate warmer  
gently push the center of the drawer.  
Do not use the plate warmer to  
reheat, cook or keep food and drinks  
warm. Condensation from food or  
drinks could cause moisture  
damage to the appliance.  
Controls  
Use pot holders when removing  
dishes.  
The drawer can hold a maximum of  
33 lbs (15 kg).  
The floor of the warming drawer has a  
non-slip mat to prevent plates and  
dishes from sliding when the drawer is  
opened and closed.  
The controls include the temperature  
selector and the On/Off button. They  
are only visible when the drawer is  
open.  
The indicator at the front shows if the  
plate warmer is turned on or off.  
7
 
 
Using the plate warmer  
Warming dishes  
Selecting a temperature  
^ Place the dishes in the plate warmer.  
^ Select a temperature.  
^ Turn the appliance on (j).  
The button will light.  
The temperature selector allows you to  
select a temperature between 86 ° and  
122 °F (30 ° and 50 °C).  
Do not turn the knob  
counterclockwise past the 12 o’clock  
position or clockwise past the  
6 o’clock position. Forcing it beyond  
these positions will damage the  
temperature selector.  
^ Close the drawer.  
^ The indicator at the front of the  
appliance lights showing that the unit  
is on.  
^ Turn the appliance off (k), when  
removing the warmed dishes.  
When the selected temperature is  
reached, the heating element will turn  
off. It turns on again, when the unit  
cools below the selected temperature.  
^ Pull the drawer out all the way to  
remove the dishes.  
The optimum temperature to preheat  
cups and glassware is about 105 °F  
(40 °C). When prewarming cups to this  
temperature, the drinks will not cool as  
fast and the cup itself is still cool  
enough to touch.  
8
 
 
Using the plate warmer  
Warming times  
Capacity  
Various factors will affect the warming  
times:  
The quantity which can be loaded will  
depend on the size of your dishes.  
– type and thickness of the dishes,  
– quantity,  
Example:  
– 25 Cappuccino cups or  
– 56 Espresso cups  
– how the dishes are arranged, and  
– temperature setting.  
As you use the plate warmer you will  
learn which settings suit your needs  
best.  
As a guideline:  
It will take approx. 30 - 40 minutes to  
evenly warm dishes at the maximum  
temperature setting of 122°F (50°C).  
Insert the cups or glassware upside  
down in the plate warmer to ensure  
an even warming.  
The maximum load is 33 lbs (15 kg).  
9
 
 
Cleaning and care  
Cleaning the plate warmer  
Non-slip mat  
The mat can be removed to clean the  
bottom of the drawer.  
Let the drawer cool before cleaning.  
Never use abrasive cleaners,  
^ Clean the mat by hand with warm  
scouring pads, steel wool or caustic  
(oven) cleaners on the plate warmer.  
They will damage the surface.  
water and liquid dish soap.  
^ Dry thoroughly. Do not return the mat  
until it is completely dry.  
The exterior of the plate warmer can be  
cleaned with warm water and liquid  
dish soap applied with a soft sponge.  
Wipe dry using a soft cloth.  
Stainless steel  
Stainless steel surfaces can be cleaned  
using a non-abrasive stainless steel  
cleaner.  
To help prevent resoiling, a conditioner  
for stainless steel can also be used.  
Apply sparingly with even pressure.  
10  
 
 
Frequently asked questions  
Repairs to electrical appliances must only be carried out by a qualified  
technician in accordance with local and national safety regulations. Repairs  
and other work by unqualified persons could be dangerous. The manufacturer  
cannot be held responsible for unauthorized work.  
Why are the dishes not warm enough?  
Possible fault  
Fix  
The appliance is turned off.  
Turn the appliance on with the On/Off  
button.  
The wrong temperature was selected. Check the temperature setting.  
The dishes need more time to warm.  
Why dishes are not warm?  
Possible fault  
Increase the timer setting.  
Fix  
The main fuse has blown.  
Why are the dishes too hot?  
Possible fault  
Restore power.  
Fix  
The temperature control is faulty.  
Call Technical Service.  
Why does the On/Off button not light when turned on?  
Possible fault Fix  
The indicator light for the On/Off button Call Technical Service.  
is bad.  
11  
 
 
After sales service  
In the event of a fault which you cannot  
correct yourself please contact the  
Miele Technical Service  
Department.  
U
V
1-800-999-1360  
[email protected]  
1-800-565-6435  
[email protected]  
When contacting the Technical Service  
Department, please quote the model  
and serial number of your appliance  
both of which are shown on the  
enclosed data plate.  
Adhere the data plate to the box below.  
Make sure the model given on the data  
plate matches that of this manual.  
12  
 
 
Installation Instructions  
 
 
Help protect our environment  
Disposal of the packing  
material  
Disposal of an old appliance  
Old appliances contain materials which  
can be recycled. Please contact your  
local recycling center about potential  
recycling.  
The transport and protective packing  
materials are environmentally safe for  
disposal and may be recycled.  
Ensure that the appliance presents no  
danger to children while being stored  
for disposal.  
Ensure that any plastic wrap is  
disposed of safely and kept out of the  
reach of children. Danger of  
suffocation!  
Please recycle.  
14  
 
 
Installation  
Installation Safety Instructions  
When installed in combination with  
another appliance, the plate  
warmer must always be installed  
beneath the other appliance. The  
combination appliance can be set  
without a base directly onto the plate  
warmer. A shelf between the  
Before installation make sure that  
the voltage and frequency listed on  
the data plate correspond with the  
household electrical supply. This data  
must correspond in order to avoid risk  
of damage to the appliance. If in doubt,  
consult a qualified technician.  
appliances is not necessary.  
To install the combination  
appliance please read the manual  
supplied with that machine.  
The electrical outlet should be  
easily accessible after the unit is  
installed.  
This appliance is not designed for  
maritime use or for use in mobile  
installations such as recreational  
vehicles or aircraft. However, under  
certain conditions it may be possible for  
an installation in these applications.  
Please contact the Miele Technical  
Service Department with specific  
requirements.  
Only install the plate warmer in  
combination with other built-in  
appliances recommended by the  
manufacturer. If installed with  
appliances not recommended, the  
warranty is void since the manufacturer  
cannot guarantee its safety.  
To install the plate warmer in  
combination with another  
appliance, a built-in shelf must exist in  
the cabinet to support the weight of  
both appliances.  
15  
 
 
Installation  
Combination possibilities  
Coffee system  
16  
 
 
Installation  
Steam oven  
17  
 
Installation  
Installing the appliance  
Aligning the appliance front  
^ Set the plate warmer into the niche,  
push is all the way in and align it at a  
right angle.  
After installing the combination  
appliance it may be necessary to align  
the appliance front and/or even the gap  
between the plate warmer and the  
combination machine.  
Flat washers are supplied beneath the  
knurled nuts, which fix the drawer to the  
telescopic runners.  
^ Open the drawer and fix the  
appliance with the two supplied  
screws at the side panels of the  
cabinet.  
^ Loosen the knurled nuts and take the  
drawer out.  
^ Install the combination appliance  
regarding the manual supplied with  
that machine.  
^ Align and even the gap with the flat  
washers by changing their position  
(above or below the drawer), on both  
sides.  
18  
 
 
Installation  
Electrical connection  
Note to the installer  
The electrical installation instructions  
for any appliance installed in  
combination with the plate warmer  
must be observed.  
Please leave these instructions with  
the consumer.  
Power supply  
This appliance is equipped with an  
approx. 6 ft (approx. 1.8 m) long power  
cord with plug ready for connection to a  
120 V, 15 A, 60 Hz power supply.  
When another appliance is installed  
in combination with the plate warmer  
to the same circuit breaker,  
operating both appliances at the  
same time may cause an overload. If  
in doubt consult a qualified  
electrician.  
All electrical work should be done  
by a qualified technician, in strict  
accordance with national and local  
safety regulations.  
Installation, repairs and other work  
by unqualified persons could be  
dangerous and may void the  
warranty.  
Make sure power is not supplied to  
the appliance while installation or  
repair work is being performed.  
WARNING:  
THIS APPLIANCE MUST BE  
GROUNDED  
19  
 
 
All rights reserved/1605  
M.-Nr. 06 405 620 / 01  
en - US  
 

MTD Automobile Accessories 143 660 User Manual
Navman Fish Finder 4432 User Manual
NEC Video Game Controller nec User Manual
Nextar Digital Photo Keychain N1 517 User Manual
Nikon Film Camera 550AS User Manual
Nikon Webcam F65D User Manual
NordicTrack Treadmill 307040 User Manual
Panasonic All in One Printer CM0310DY0 CD User Manual
ParaBody Home Gym 842 User Manual
ParaBody Home Gym 810101 User Manual