MIL-S1000
User’s Manual
Table of Contents
Chapter 1 Introduction
Package Contents……….…………………………………….. 1-2
Device Description, Features and Capabilities …………… 1-3
MIL-S1000 Front and Rear Panels……….………………
1-3
8 ports 10/100Base-TX Module…….……………………… 1-5
8 ports 10/100Base-TX Module Features …..….… 1-5
2 ports 100Base-FX Fiber Module………………….…… 1-8
2 ports 100Base-FX Fiber Module Features ….….. 1-9
4 ports 100Base-FX Fiber Module ………..…………… 1-11
4 ports 100Base-FX Fiber Module Features ………. 1-12
1000Base-SX/LX Fiber Module …………………………..1-14
1000Base-SX/LX Fiber Module Features ……….…..1-14
Chapter 2 Planning your Network
10Base-T Ethernet Network Guidelines……………………. 2-1
100Base-T Ethernet Network Guidelines…………………… 2-2
1000Base-SX and LX Network Guidelines…………………. 2-3
Network Planning………………………………………………. 2-3
Expanded Networks………………………………….……….. 2-4
10Base-TX Networks…………………………………….. 2-4
100Base-TX Networks…………………………………… 2-5
Collapsed Backbone Line…………………………………….. 2-6
Fileserver Link………………………………………………….. 2-7
Multiport Bridge with High-Bandwidth Backbone……….. 2-9
Chapter 3 Installation
Choosing A Location………………………………………….. 3-1
Rack Installation……………………………………………….. 3-2
Supplying Power………………………………………………. 3-3
Connecting the Switch..……………………………………...
3-4
Chapter 4 Module Install and Removed
Handling the Modules…………………………………………. 4-1
Module Setup and installation……………………………… 4-2
Installing the Modules………………………………………… 4-3
Installing 10/100Base-TX Modules…… ………………. 4-3
Installing 100Base-FX Modules…… …………………… 4-3
Installing 1000Base-SX/LX Modules…… …………….. 4-4
Removing the Modules…………………………………………. 4-4
Appendix A Pin and Cable Specification…………..…. A-1
Appendix B Technical Specification……………….…… B-1
Chapter 1 Introduction
MIL-S1000 switches are multi-speed network devices
combining Ethernet, Fast Ethernet and Gigabit Ethernet
capabilities in a single compact, rack-mountable cabinet.
Combining 10Mbps Ethernet, 100Mbps Fast Ethernet and
Gigabit Ethernet interfaces in one unit allows these
switches to unclog existing LANs and provide a path to
efficient, high-speed networking.
The MIL-S1000 switch is a combination of a 4-slot host
cabinet which accepts 4 different media modules and One
RS-232 port for SNMP(Optional). A maximum configuration
of 32 x 10/100Base-Tx switched ports can be achieved
using 4×8 port 10/100Base-Tx modules. In the same way,
a maximum configuration of 32×10/100Base-TX or
16×100Base-FX ports or 4x 1000Base-SX can be
accommodated in the host cabling. Any of the above
modules can be integrated to give up to many different
configurations.
Package Contents
Rubber Feet
Power Cord
Manual
Warranty Card
Rack-Mount Kit
Figure 1-1. Package Contents
The MIL-S1000 package contains the following:
! MIL-S1000 switch
! AC power cord
! Rack mounting kit
! Four Rubber feet
! Warranty card
! User manual
Device Description, Features and Capabilities
MIL-S1000 Front and Rear Panels
This section describes the features on the front and rear
panels of the MIL-S1000 unit.
Figure 1-2. Front Panel
Figure 1-3. Rear Panel
All LED status indicators are located on the FRONT panel
of the switches. They provide a real-time indication of
system and operational status. The ports for connections to
other devices and networks are also on the front panels,
along with the crossover switches. The following sections
provide descriptions of the LED indicators and ports.
LED
Indicators
Explanation
The red power indicator is illuminated
when power is provided to the switch and
the switch is turned in the ON position.
Power
Green
Link/Activity
indicators
are
illuminated when the switch detects a
connection to that port. The indicator
Link/Activity blinks when data is transmitted over the
network connected to that port.
When a port is not connected, the
indicator is off.
Red Full Duplex/Col indicators
are illuminated when that port is
in full duplex mode. The indicator
is off when that port is in half
duplex mode.
When a collision occurs on the network
connected to a port, that Full Duplex/Col
indicator blinks.
Full
Duplex/Col
Green 100Mbps indicators are illuminated
when the port is operating in 100Mbps
mode. The indicator is off when the port is
100Mbps
operating in 10Mbps mode.
" Power Port
The power port accepts the power plug.
" Power Switch
The power switch, located on the rear panel, controls the
power supply.
8 ports 10/100Base-TX Module
Figure 1-4. 8 port 10/100Base-TX Module
When installed into a MIL-S1000 switch, the 10/100Base-
TX Module provides 8 10/100Mbps Switch ports which can
connect the MIL-S1000 to a 10Mbps or 100Mbps switch or
end station.
8 Ports 10/100Base-Tx Module Features
" 8 10/100Base-TX N-Way Switch ports.
" Conforms to IEEE 802.3 10Base-T and IEEE 802.3u
100Base-TX and IEEE 802.3x standards
" Store and forward switch architecture for abnormal
packet filtering
" Support for half and full duplex on all ports
" Backplane up to 2.4Gbps
" 2M memory Buffer support
" Automatic address learning with 12K address entry
storage
" Filtering and forwarding rate of 14,880~148,800
packets per second
DIP Switch with Link Mode
The 8 port 10/100Base-TX module provides dip switch for
1 to 4 port to adjust link mode with other network devices.
Another 4 ports use auto-negotiation protocol only. There
are three type of link mode can be chosen, Auto-
negotiation, 100Mbps/Full duplex and 10Mbps/Full duplex.
Port 1
ON
Port3
Port 2
Port 3
Port 4
Port 5
Port 6
Port 7
Port 8
adjustable
ports
Port1
DIP Sw itch for
Port 1 to Port 4
5
1 2 3 4
6 7 8
Port2
OFF
Port4
FullDuplex
10M
Auto-
negotiation
1
2
100M
Figure 1-5. Dip switch location and mode settings
If you adjust to auto-negotiation, then the DIP for 100Mbps
and 10Mbps is not effective. If you adjust to Full duplex,
then the DIP for 100Mbps and 10Mbps is effective.
The following Table 1-1. lists the ports’ operating modes
based on the DIP switch position.
PORT 1
PORT 2
PORT3
PORT4
SW
ON
1
Full
2
10M
3
Full
4
10M
5
Full
6
10M
7
Full
8
10M
OFF Auto 100M Auto 100M Auto 100M Auto 100M
Table 1-1. 8 Ports 10/100Base-TX Module DIP switch functions
2 ports 100Base-FX Fiber Module
Figure 1-6. 2 port 100Base-FX Module Front View
When installed into a MIL-S1000 switch, this Module
provides a 100Mbps Fast Ethernet fiber port which can be
used to:
# Connect the Switch to the backbone of your network;
that is, to a basement switch, hub or router
# Connect the Switch to a 100Mbps server or end-station
An ST, SC, MT-RJ or VF-45 connector provides the link to
the multi-mode fiber cabling and two indicators show the
status of the Module at-a glance. A DIP-switch sets the
operating mode to half duplex or full duplex (default).
DIP Sw itch Location
Port 1
Port 2
Figure 1-7. Dip switch location and mode settings
The following Table 1-2. lists the ports’ operating modes
based on the DIP switch position.
PORT 1
1
Half-Duplex
Full-Duplex
PORT 2
2
Half-Duplex
Full-Duplex
SW
ON
OFF
Table 1-2. 2 ports 100Base-FX Fiber ModuleDIP switch functions
2 ports 100Base-FX Fiber Module Features
" Conforms to IEEE 802.3u Fast Ethernet standard
" Support for SC, ST, MT-RJ or VF-45 fiber connectors
(optional)
" Supports half and full duplex modes via DIP switches
" Store-and-forward switch architecture for abnormal
packet filtering
" 2 switching 100Mbps Fiber Ethernet ports
" Backplane up to 2.4Gbps
" Automatic address learning with 12K address entry
storage
" Filtering and forwarding rate of 148,800 packets per
second
" 100Base-FX uses 62.5/125 micron multi-mode fiber
4 Ports 100Base-FX Fiber Module
Figure 1-8. 4 port 100Base-TX/FX Front View
When installed into a MIL-S1000 switch, this Module
provides 4 x 100Mbps Fast Ethernet fiber ports which can
be used to:
# Connect the Switch to the backbone of your network;
that is, to a basement switch, hub or router.
# Connector the Switch to a 100Mbps server or end
station.
An ST, SC, MT-RJ or VF-45 connector provides the link to
the multi-mode fiber cabling and three LEDs show five
status of the Module at-a glance. A DIP-switch sets the
operating mode to half duplex or full duplex (default).
Port 1
Port 2
DIP Sw itch Location
Port 3
Port 4
Figure 1-9. Location and setting duplex mode
The following Table1-3. lists the ports operating modes
based on the DIP switch position.
PORT 1
1
Half-Duplex
Full-Duplex
PORT 2
2
Half-Duplex
Full-Duplex
PORT3
3
Half-Duplex
Full-Duplex
PORT4
4
Half-Duplex
Full-Duplex
SW
ON
OFF
Table 1-3. 4 ports 100Base-FX Fiber Module DIP switch functions
4 ports 100Base-FX Fiber Module Feature
" Conforms to IEEE 802.3u Fast Ethernet standard
" Support SC, ST, MT-RJ or VF-45 fiber connector
(optional)
" Support half and full duplex via DIP switches
" Store-and-forward switch architecture for abnormal
packets filtering
" Backplane up to 2.4Gbps
" Automatic address learning with 12K address entry
storage
" Filtering and forwarding rate 148,800 packets per second
for 100Mbps
" 100Base-FX uses 62.5/125 micron multi-mode fiber
1000Base-SX/LX Fiber Module
Figure 1-10. 1000Base-SX/LX Front View
When installed into a MIL-S1000 switch, the 1000Base-
SX/LX Module provides 1 Gigabit Ethernet ports which can
connect the MIL-S1000 to a Gigabit Backbone Switch or
Server with Gigabit NIC.
1000Base-SX/LX Fiber Module Features
" Conforms to IEEE 802.3z draft 4.2 and 802.3x standard
" 1x1000Base-SX/LX Ethernet Port
" 3M memory buffer support
" Standard auto-negotiation for speed, duplex mode and
flow-control for MII and GMII PHYs
" Backpressure option and Limit4 option for half duplex
" Automatic address learning with 12K address entry
storage
DIP Sw itch Location
Figure 1-11. Location and setting duplex mode
If you adjust to Enable N-Way, then the DIP for Half-Duplex
and Full-Duplex is not effective. If you adjust to Disable N-
Way, then the DIP for Half-Duplex and Full-Duplex is
effective.
The following Table 1-4. lists the ports’ operating modes
based on the DIP switch position.
Gigabit Port
SW
ON
OFF
1
2
Disable N-way
Enable N-way
Half Duplex
Full Duplex
Table 1-4. 1000Base-SX/LX Fiber Module DIP switch functions
Chapter 2 Planning your Network
Before you install your MIL-S1000, you should review the
guidelines for setting up Ethernet networks. Further, you
should plan your network to take maximum advantage of
its switching capabilities.
10Base-T Ethernet Network Guidelines
# The maximum length of a 10Base-T cable segment is
100 meters (328 feet).
# The maximum number of nodes on a 10Base-T
segment is one (1) for regular 10Base-T.
# The recommended cable type is EIA/TIA Category 3 or
higher.
# The maximum network diameter is 500 meters (1,640
feet) for Ethernet networks.
# The maximum number of segments between any two
nodes in the network is five.
# The maximum number of hubs or repeaters between
any two nodes in the network is four.
100Base-TX Ethernet Network Guidelines
# The maximum length of a 100Base-TX cable segment
is 100 meters (328 feet).
# The maximum number of hubs on a 100Base-TX
segment is one if using Class I hubs and two if using
Class II hubs.
# The recommended cable type is EIA/TIA Category 5
unshielded twisted-pair.
# The maximum network diameter is 200 meters (656
feet) when using Class I hubs and 205 meters (672.5
feet) when using Class II hubs.
100BASE-FX Network Guidelines
# In half duplex mode, the fiber optic segment cannot
exceed 412m (1,135ft) in length.
# In full duplex mode, the fiber optic segment cannot
exceed 2km (6562 ft) in length.
1000BASE-SX and LX Network Guideline
1000BASE-SX
# In multi-mode, the fiber optic segment cannot exceed
220m(62.5/125µm) or 500m(50/125µm) in length.
1000BASE-LX
# In multi-mode, the fiber optic segment cannot exceed
550m(62.5/125µm), 550m(50/125µm) in length.
# In single-mode the fiber optic segment cannot exceed
10km(9/125µm).
Network Planning
Using a switch, such as a MIL-S1000, can expand network
topologies and enhance network performance.
Each port on a switch connects to a separate network with
its own collision domain. Separating networks with these
switches allows you to expand 10Base-T networks past the
four-hub limit and expand 100Base-TX networks past the
one or two hub limit.
These switches also filter incoming traffic. On standard
hubs and repeaters, any data received on a port is
forwarded to all of the other ports. On switches, data
received on one port is forwarded only to the port of the
destination device, and if the traffic is local, the data is not
forwarded at all. Also, switches can forward multiple data
transaction at once.
To expand your network topology or enhance network
performance, use the MIL-S1000 as collapsed backbone or
to increase file server performance, to segment large
networks, to interconnect 10Mbps networks with 100Mbps
networks, or to overcome the limitations of 10Base-T and
100Base-TX networks.
Expanded Networks
You can expand your 10Base-T or 100Base-TX or
1000Base-SX/LX network beyond its hub limit by adding a
MIL-S1000.
10Base-T Networks
10Base-T Networks are limited to four hubs between any
two nodes. By adding your MIL-S1000 to a network, you
can divide that network into segments with their own
collision domains. In other words, you can connect one
10Base-T network with four hubs to your MIL-S1000. Then
you can connect another 10Base-T network with four hubs
to your MIL-S1000. You will then have one network with
two collision domains, allowing four hubs on each port.
Figure 2-1. Expanding your 10Base-T Network
100Base-TX Networks
The hub limit of a 100Base-TX network depends on the
class of the hub in the network. With a Class I hub, the
network is limited to one hub. With a Class II hub, the
network is limited to two hubs.
However, you can expand your 100Base-TX network that
includes either class of hub by adding a MIL-S1000. With
the MIL-S1000 added to your 100Base-TX network, you
can separate that network into individual segments with
their own collision domains. In other words, you can
connect one 100Base-T network with one or two hubs to
the MIL-S1000, and you can connect another 100Base-TX
network with one or two hubs to the MIL-S1000. You will
then have one network with two collision domains.
Figure 2-2. Expanding your 100Base-TX network (Class I)
Collapsed Backbone Link
Traditionally, bridges and routers have been used to link
local area networks into one interconnected network. But
these devices involve difficult management and long traffic
delays.
The MIL-S1000 providers multiport bridges with short
delays, easy setup and maintenance, making it ideal for
backbone links. Also, the Built-in filtering on this hub
deceases network traffic, while the multiple ports that
communicate
performance.
simultaneously
increases
network
One or more of your hub's 100Mbps or 1000Mbps ports
can be used as a high-speed backbone link to other hubs
serving as collapsed backbones.
Figure 2-3. MIL-S1000 100/1000 Hub in a collapsed backbone
link
Fileserver Link
100Base Solution
With a fileserver link, you can increase file server
performance by increasing the Hub's bandwidth between
one or more fileservers and the workgroups they serve.
If you connect 10Mbps workgroup hubs to the 10Mbps
ports on the MIL-S1000, traffic in one workgroup will not
interfere with the performance of another workgroup.
Figure 2-4. Fileserver Link
Connecting servers through 100Base-TX ports increases
performance to the clients, even if the clients are on
10Base-T segments.
Because multiple 10Base-T devices can access the file
server at the same time through a 100Base-TX connection,
performance increases to beyond the performance of
standard 10Base-T or 100Base-TX hubs. Operating the
MIL-S1000 at full duplex further increases performance
1000Base Solution
You can upgrade your server with a Gigabit Ethernet NIC,
and introduce a Gigabit backbone switch too.
This
contains several switch ports which provides much faster
access to your server with minimum disruption. See Figure
16.
Multiport Bridge with High-Bandwidth Backbone
With a MIL-S1000, you can divide large network to ease
congestion, and connect 10Base-T networks to 100Base-
TX or 100Base to 1000Base networks for more flexibility.
Adding your MIL-S1000 to a large network creates more
segments in that network. The MIL-S1000 built-in filtering
function separates a segment's local traffic from network
traffic, reducing the amount of network traffic and easing
congestion.
Figure 2-5. Used as a Multiport Bridge
Using your hub, you can also connect 10Base-T networks
and 100Base-TX and 1000Base-SX/LX networks together
for more flexibility in your network topology. As in the
Figure 16 shown above, the MIL-S1000 can connect
through one port to a 10Base-T network, and through
another port, connect to a 100Base-TX port, creating one
network. This switch can also connect to a 1000Base-LX or
SX port.
Chapter 3 Installation
The MIL-S1000 can be installed quickly and easily.
However, for an installation with minimum impact on
the existing network, please read this chapter carefully.
Installing a MIL-S1000 involves three steps:
1. Choosing a location
2. Supplying power
3. Connecting the switch
Choosing A Location
The location of the switch is based on the following criteria:
" Avoid dusty locations.
" Avoid electromagnetic noisy areas, such as locations
close to power transformers or radio transmitters.
" Avoid temperatures below 32 Degrees Fahrenheit and
over 122 Degrees Fahrenheit.
" Allow a clear view of the front panel LED indicators.
" Allow easy access to the front panel ports and the rear
panel switches.
After choosing an appropriate location, you can install the
switch on a desktop or in a rack.
Figure 3-1. Attaching self-adhesive feet for desktop installation
Rack Installation
Your switch comes with two rack mounting brackets. you
can use these brackets to mount the switch on an EIA
standard 19" rack. Attach the brackets to the switch, using
the screws provided.
Figure 3-2. Attaching the mount brackets for rack installation
Next, install the switch in the rack using the screws
provided to attach the brackets to the rack.
Supplying Power
The MIL-S1000 switch is equipped with a universal
switching power supply that accepts AC input voltages
from 100 to 240VAC and 50 to 60 Hz.
To supply power to your switch:
1. Plug the connector of the power cord into the power port
on the rear panel of your switch.
2. Plug the other end of the power cord into an AC wall
outlet.
3. Set the power switch to ON and verify that the Power
LED is lit. If it is not, check the following:
" The power switch is in the ON position.
" The power cord is properly connected to the wall
outlet and to the power connection on the switch.
" The wall outlet is functional.
Note: Network cable segments can be connected or
disconnected from the switch while the power is on, without
interrupting the operation of the switch.
Connecting the Switch
You can connect your switch to network devices such as
desktops and workgroups or to other hubs.
Before connecting your switch to a desktop or workgroup
make sure that:
# The 10Base-T twisted pair Ethernet cabling is Category
3 or above.
# The 100Base-TX Fast Ethernet cabling is tested
Category 5.
# The 100Base-FX fiber cabling is 62.5/125 micron multi-
mode fiber.
# The 1000Base-SX/LX fiber cabling is 50/125, 62.5/125
micron multi-mode or 9/125 micron single-mode fiber.
Chapter 4. Module Installation and Removal
WARNING
Before installing the Modules into a MIL-S1000, you must
disconnect the Switch from the main power supply.
Handling the Modules
The Module can be easily damaged by electrostatic
discharge. To prevent damage, please observe the
following:
# Do not remove Modules from their packaging until you
are ready to install it into a Switch.
# Do not touch any of the pins, connections or
components on the Modules.
# Handle the Modules only by its edges and front panel.
# Always wear an anti-static wristband connected to a
suitable grounding point.
# Always store or transport Modules in appropriate anti-
static packaging.
Module Setup and Installation
1. Ensure that the Switch is disconnected from the main
power supply and that you are wearing an anti-static
wrist-band connected to a suitable grounding point.
2. Place the Switch on a flat surface. Using a small cross-
bladed screwdriver, remove the blanking plate from the
rear of the Switch. Do not remove any other screws from
the rear of the Switch.
3. Keep the blanking plate and screws in a safe place. If
you remove the Module at any time, you must replace
the blanking plate to prevent dust and debris from
entering the Switch and to aid the circulation of cooling
air.
4. Hold the Module so that the text on the front panel is
oriented correctly, and insert it into the Switch, ensuring
the connectors are fully engaged. Tighten the two
captive thumbscrews that secure the Module in place.
Figure 4-1. Insert the module
Installing the Modules
Installing 10/100Base-TX Modules
a. Insert the RJ-45 connector on your cable into the socket
of the Module.
b. Connect the other end of the cable to an appropriate
device with a 100Mbps Fast Ethernet or 10Mbps
Ethernet twisted pair interface.
c. Power up the Switch.
Installing 100Base-FX Modules
a. Remove the protective plastic covers from the fiber
connectors on the Module.
b. Ensure that the Switch is powered up.
c. Plug the ST (or SC) connector on the fiber cable into the
fiber socket on the Module.
d. Connect the other end of the fiber optic segment to an
appropriate device fitted with a 100Mbps adapter.
Check the LED indicators on the front of the Switch to
ensure that the Module is operating correctly.
Installing 1000Base-SX/LX Modules
a. Remove the protective plastic covers from the fiber
connectors on the Module.
b. Ensure that the Switch is powered up.
c. Plug the SC connector on the fiber cable into the fiber
socket on the Module.
d. Connect the other end of the fiber optic segment to an
appropriate device fitted with a 1000Mbps adapter.
Check the LED indicators on the front of the Switch to
ensure that the Module is operating correctly.
Removing the Modules
a. Ensure that the power supply and the backbone
connection cables are disconnected from the Switch.
b. Place the Switch on a flat surface. Undo the two captive
thumbscrews securing the Module into the Switch. Do
not remove any other screws from the rear of the
Switch.
c. If you are not installing another Module immediately, you
must replace the blanking plate to ensure that dust and
debris do not enter the Switch, as well as to aid
circulation of cooling air.
Appendix A. Technical Specifications
Compatibility with Ethernet Standards:
The MIL-S1000 has been designed in accordance with
IEEE Standard 802.3 and 802.3u and 802.3z.
Power Input:
Voltage
Frequency
100V AC to 240V AC
50Hz to 60Hz
Environment:
Operating
Storage
Temperature 0 to 45
-40 to 70
10% to 90% RH
Humidity 10% to 90% RH
Dimensions:
440mm x 225mm x 66mm
EMI & Safety:
FCC Class A, CE CISPR 22, UL/CSA
Physical Characteristics:
Buffer Size
2 Mbytes memory share per 10/100Base-TX module, maxi
8 Mbytes
2 Mbytes memory share per 100Base-FX module, maxi 8
Mbytes
3 Mbytes memory share per 1000Base-SX/LX module,
maxi 12 Mbytes
Address Table
12K entry MAC Address table / per module
Switching Architecture
Store and Forward
Forwarding Rate
14,880 pps/10Base-T port
148,800 pps/100Base-TX port
148,800 pps/100Base-FX port
1,488,000 pps/1000Base-SX/LX port
Filtering Rate
14,880 pps/10Base-T port
148,800 pps/100Base-TX port
148,800 pps/100Base-FX port
1,488,000 pps/1000Base-SX/LX port
LED Indicators
Link/Transmit/Receive data indicator per port
Collision/Full-Duplex indicator per port
100Mbps indicator for 10/100Mbps Module
Power on/off indicator
Appendix B. Pin Assignments
RJ-45 station ports can be attached to any device which
use a standard network interface (e.g., a workstation,
server, bridge or router). RJ-45 daisy-chain ports can be
cascaded to a station port on similar networking devices
(e.g., another switch or hub). Use unshielded twisted-pair
(UTP) for RJ-45 connections: 100 ohm Category 3,4 or 5
cable for 10Mbps connections or 100 ohm Category 5
cable for 100Mbps connections. Also be sure that the
length of any twisted-pair connection does not exceed 100
meters (328 feet).
RD
1
2
3
RD
4
5
TD
TD
6
7
8
Figure B-1. RJ-45 Connector
Pin
1
2
3
6
Pin Station Ports 1 ~ 8
Receive Data +
Receive Data -
Transmit Data +
Transmit Data -
Not Used
Cascade Ports
Transmit Data +
Transmit Data -
Receive Data +
Receive Data -
Not Used
4,5,7,8
Table B-1. RJ-45 Pin Assignments
Schematics for both straight and crossover twisted-pair
cable are shown below.
Straight-Through
Cross-Over / Swap
Switch
1 RD +
2 RD -
3 TD +
6 TD -
Adapter
Switch
1 RD +
2 RD -
3 TD +
6 TD -
Hub
1 TD +
2 TD -
3 RD +
6 RD -
1 RD +
2 RD -
3 TD +
6 TD -
|