OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
Catalog No.
No de Cat.
Catálogo No.
1670-1
1675-1
1675-6
1676-6
HEAVY-DUTY HOLE HAWG®
FOREUSE EXTRA-ROBUSTE HOLE HAWG®
TALADRO HEAVY-DUTY HOLE HAWG®
TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE
MANUEL DE L'UTILISATEUR.
PARAREDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL
DEL OPERADOR.
POWER TOOL USE AND CARE
SPECIFIC SAFETY RULES
GENERAL SAFETY RULES-FOR ALL BATTERY OPERATED TOOLS
WARNING
16. Do not force the power tool. Use the
correct power tool for your applica-
tion. The correct power tool will do the
job better and safer at the rate for which
it was designed.
1. Use auxiliary handles supplied with
the tool. Loss of control can cause
personal injury.
2. Wear ear protectors with impact
drills. Exposure to noise can cause
hearing loss.
READ ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in electric shock, fire and/or
seriousinjury.Theterm"powertool"inallofthewarningslistedbelowreferstoyour
mains-operated (corded) power tool or battery-operated (cordless) power tool.
17. Do not use the power tool if the switch
doesnotturnitonandoff.Anypowertool
that cannot be controlled with the switch is
dangerous and must be repaired.
3. Hold power tools by insulated grip-
ping surfaces when performing an
operation where the cutting tool may
contact hidden wiring or its own cord.
Contact with a “live” wire will make ex-
posed metal parts of the tool “live” and
shock the operator.
SAVE THESE INSTRUCTIONS
18. Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories,
or storing power tools. Such preven-
tive safety measures reduce the risk of
starting the tool accidentally.
PERSONAL SAFETY
WORK AREA SAFETY
1. Keep work area clean and well lit.
Cluttered or dark areas invite acci-
dents.
9. Stay alert, watch what you are do-
ing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the influence of drugs, alcohol
or medication. Amoment of inattention
while operating power tools may result
in serious personal injury.
4
Maintain labels and nameplates.
These carry important information.
If unreadable or missing, contact a
MILWAUKEE service facility for a free
replacement.
19. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tools or
these instructions to operate power
tools. Power tools are dangerous in the
hands of untrained users.
2. Do not operate power tools in ex-
plosive atmospheres, such as in the
presence of flammable liquids, gases,
or dust. Power tools create sparks which
may ignite the dust or fumes.
5. WARNING! Some dust created by
power sanding, sawing, grinding, drill-
ing, and other construction activities
contains chemicals known to cause
cancer, birth defects or other reproduc-
tive harm. Some examples of these
chemicals are:
3. Keep children and bystanders away
while operating a power tool. Distrac-
tions can cause you to lose control.
10. Use safety equipment. Always wear
eye protection. Safety equipment such
as dust mask, non-skid safety shoes,
hard hat, or hearing protection used
for appropriate conditions will reduce
personal injuries.
20. Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool's operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
•
•
lead from lead-based paint
ELECTRICAL SAFETY
crystalline silica from bricks and cement
and other masonry products, and
11. Avoid accidental starting. Ensure the
switchisintheoff-positionbeforeplug-
ging in. Carrying tools with your finger on
the switch or plugging in power tools that
have the switch on invites accidents.
4. Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
•
arsenic and chromium from chemically-
treated lumber.
21. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
Your risk from these exposures varies,
depending on how often you do this
type of work. To reduce your exposure
to these chemicals: work in a well ven-
tilated area, and work with approved
safety equipment, such as those dust
masks that are specifically designed to
filter out microscopic particles.
12. Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotat-
ing part of the power tool may result in
personal injury.
5. Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
Thereisanincreasedriskofelectricshock
if your body is earthed or grounded.
22. Use the power tool, accessories and
tool bits etc., in accordance with
these instructions and in the manner
intended for the particular type of
power tool, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
13. Do not overreach. Keep proper foot-
ing and balance at all times. This
enables better control of the power tool
in unexpected situations.
6. Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric
shock.
14. Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothingandglovesawayfrommoving
parts. Loose clothes, jewellery, or long
hair can be caught in moving parts.
7. Do not abuse the cord. Never use the
cord for carrying, pulling, or unplug-
ging the power tool. Keep cord away
from heat, oil, sharp edges, or mov-
ing parts. Damaged or entangled cords
increase the risk of electric shock.
SERVICE
23. Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool
is maintained.
15. If devices are provided for the connec-
tion of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of these de-
vices can reduce dust-related hazards.
8. When operating a power tool out-
doors, use an extension cord suitable
for outdoor use. Use of a cord suitable
for outdoor use reduces the risk of elec-
tric shock.
2
3
Specifications
FUNCTIONAL DESCRIPTION
Capacity
Wood
Steel
1
Volts
Cat. No. AC
No Load
RPM
WithShip
Auger Bit
With
Twist Bit
With Auger
Bit
With
Selfeed Bit
Speed
-
1670-1
1675-1
120
120
900
1-1/2"
1-1/4"
1-1/2"
1-1/4"
1-1/2"
1-1/4"
1-1/2"
7/16"
5/16"
1/2"
1-1/2"
1-1/8"
1-1/2"
1-1/8"
1-1/2"
1-1/8"
1-1/2"
2-9/16"
1-3/8"
4-5/8"
1-3/8"
4-5/8"
1-3/8"
4-5/8"
9
1200
300
High
Low
8
9
7
2
1675-6
1676-6
120
120
1200
300
5/16"
1/2"
High
Low
High
Low
1200
300
5/16"
1/2"
GROUNDING
1. Spade Handle
2. Chuck
6
The grounding prong in the plug is connected
through the green wire inside the cord to
the grounding system in the tool. The green
wire in the cord must be the only wire con-
nected to the tool's grounding system and
must never be attached to an electrically
“live” terminal.
WARNING
3. Trigger Switch
4. Reversing Switch
5. Switch Handle
6. Motor Housing
7. Gear Shift Lever
8. Pipe Handle
3
9
Improperlyconnectingthegrounding
wire can result in the risk of electric
shock. Check with a qualified electri-
cian if you are in doubt as to whether
the outlet is properly grounded. Do
not modify the plug provided with
the tool. Never remove the grounding
prong from the plug. Do not use the
tool if the cord or plug is damaged.
If damaged, have it repaired by a
MILWAUKEE service facility before
use. If the plug will not fit the outlet,
have a proper outlet installed by a
qualified electrician.
5
Your tool must be plugged into an appropri-
ate outlet, properly installed and grounded in
accordance with all codes and ordinances.
The plug and outlet should look like those
in Figure A.
4
9. Insulated Gripping Surfaces
Double Insulated Tools:
Tools with Two Prong Plugs
Symbology
Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association and the National Electrical
Code. Double Insulated tools may be used
in either of the 120 volt outlets shown in
Figures B and C.
Underwriters
Laboratories, Inc.
Grounded Tools:
Tools with Three Prong Plugs
Canadian Standards
Association
Tools marked “Grounding Required” have a
three wire cord and three prong grounding
plug. The plug must be connected to a prop-
erly grounded outlet (See Figure A). If the
tool should electrically malfunction or break
down, grounding provides a low resistance
path to carry electricity away from the user,
reducing the risk of electric shock.
Mexican Approvals Marking
Volts Alternating Current
No Load Revolutions
per Minute (RPM)
Amperes
Fig. C
Fig. B
4
5
EXTENSION CORDS
TOOL ASSEMBLY
Grounded tools require a three wire exten-
Guidelines for Using Extension Cords
WARNING
Pipe Handle
sion cord. Double insulated tools can use
either a two or three wire extension cord.
As the distance from the supply outlet
increases, you must use a heavier gauge
extension cord. Using extension cords with
inadequately sized wire causes a serious
drop in voltage, resulting in loss of power
and possible tool damage. Refer to the table
shown to determine the required minimum
wire size.
•
If you are using an extension cord out-
doors, be sure it is marked with the suffix
“W-A” (“W” in Canada) to indicate that it
is acceptable for outdoor use.
The pipe handle may be used on either side
of the tool. Thread pipe handle into one of the
threaded holes in the motor housing.
To reduce the risk of injury,
always unplug tool before attaching
or removing accessories or making
adjustments. Use only specifically
recommended accessories. Others
may be hazardous.
•
Be sure your extension cord is prop-
erly wired and in good electrical
Spade Handle (Fig. 2)
condition. Always replace a damaged
extension cord or have it repaired by a
qualified person before using it.
Fig. 2
A
Installing Bits into Keyed Chucks (Fig.1)
Fig. 1
•
Protect your extension cords from sharp
objects, excessive heat and
damp or wet areas.
The smaller the gauge number of the wire,
the greater the capacity of the cord. For ex-
ample, a 14 gauge cord can carry a higher
current than a 16 gauge cord. When using
more than one extension cord to make up
the total length, be sure each cord contains
at least the minimum wire size required. If
you are using one extension cord for more
than one tool, add the nameplate amperes
and use the sum to determine the required
minimum wire size.
B
C
Recommended Minimum Wire Gauge
for Extension Cords*
Extension Cord Length
Nameplate
Amperes
25' 50' 75' 100' 150'
0 - 2.0
2.1 - 3.4
3.5 - 5.0
18 18 18 18
18 18 18 16
18 18 16 14
18 16 14 12
16 14 12 10
14 12 10
16
14
12
12
5.1 - 7.0
The spade handle can be attached to the tool
in three positions (Fig. 2). Remove the hex
head screws which secure the handle. Re-
move the handle and move it to the desired
position. To mount the handle in position C,
it is necessary to reverse the mounting holes
by turning the handle around.
1. Unplug tool.
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
2. Open the chuck jaws wide enough to
insert the bit. Be sure the bit shank and
chuck jaws are clean. Dirt particles may
prevent the bit from lining up properly.
12 10
* Based on limiting the line voltage drop to
five volts at 150% of the rated amperes.
3. Insert the bit into the chuck. Center the
bit in the chuck jaws and lift it about 1/16"
off of the bottom. Then, tighten the chuck
jaws by hand to align the bit.
READ AND SAVE ALL INSTRUCTIONS FOR FUTURE USE.
4. Place the chuck key in each of the three
holes in the chuck, turning it clockwise.
Tighten securely.
5. To remove the bit, insert the chuck key
into one of the holes in the chuck and
turn it counterclockwise.
Bit Selection
•
Use sharp bits. Sharp bits are less likely
to bind when drilling.
•
Use the proper bit for the job. There are
many types of bits designed for specific
purposes. Check the information on the
bit's packaging for proper usage.
•
Do not use bits larger than the rated
capacity of the drill. Gear damage or
motor overload may result.
6
7
Bracing for reverse rotation
Fig. 6
Bracing for forward rotation
Fig. 4
OPERATION
WARNING
Bit binding (Fig. 3)
Fig. 3
To reduce the risk of injury, wear
safety goggles or glasses with side
shields. Unplug the tool before
changing accessories or making
adjustments.
B
A
C
B
C
B
WARNING
A
Fig. 5
A
To reduce the risk of personal injury
whendrilling,alwaysholdtoolbythe
insulated gripping surfaces when
performing an operation where the
cutting tool may contact hidden wir-
ing or its own cord. Contact with a
"live" wire will make exposed metal
parts of the tool "live" and shock
the operator.
Fig. 7
D
If the bit binds, the drill will suddenly react
in the opposite direction of the rotation of
the bit. Figure 3 shows the path of reaction
(B) if the drill bit binds while being driven in
forward (A). The operator should reduce the
chances of a sudden reaction by following
the instructions listed below.
D
B
B
The operator should also prepare for a
sudden reaction by holding securely using
the pipe handle or bracing against a solid
fixed object.
A
A
WARNING
To reduce the chance of bit binding
When drilling in forward, the bit will rotate in
a clockwise direction. If the bit binds in the
hole, the bit will come to a sudden stop and
drill will suddenly react in a counterclockwise
direction.
When drilling in reverse, the bit will rotate in
a counterclockwise direction. If the bit binds
in the hole, the bit will come to a sudden
stop and the drill will suddenly react in a
clockwise direction.
When drilling with a single speed
drill or in HI with a two speed drill,
always hold the drill securely us-
ing the pipe handle, or brace the
drill against a solid fixed object in
preparation for a sudden reaction.
When drilling in LO with a two speed
drill, always brace the drill against a
solid fixed object in preparation for
a sudden reaction.
•
Use sharp bits. Sharp bits are less likely
to bind when drilling.
•
Use the proper bit for the job. There are
many types of bits designed for specific
purposes.
Figures 4 and 5 show examples of a Hole
Hawg® properly braced for forward rota-
tion.
Figures 6 and 7 show examples of the
Hole Hawg® properly braced for reverse
rotation.
•
Use the proper speed for the size
bit. Larger bits should be run at the
lower speed. Driving larger bits at high
speeds will increase the chance of the
bit binding and increase the chance of
reaction.
A. Forward (clockwise) rotation
B. Reaction
A. Reverse (counterclockwise) rotation
B. Reaction
When drilling, never use your body
to brace drill.
C. Brace drill with pipe handle here
D. Brace drill with motor housing here
C. Brace drill with pipe handle here
D. Brace drill with motor housing here
•
•
Avoid drilling warped, wet, knotty, and
or pitchy material if possible.
Never put your hands (or other body
parts) between the part of the drill
being braced and the object it is be-
ing braced against. Hands (or other
body parts) that are in the path of the
reaction can be pinched, crushed
and broken.
If the bit binds, the pipe handle or the motor
housing braced against the stud will hold the
drill in position.
If the bit binds, the pipe handle or the motor
housing braced against the stud will hold the
drill in position.
Avoid drilling in material that you suspect
contains hidden nails or other things that
may cause the bit to bind.
The direction of reaction is always opposite
of the direction of bit rotation.
Reaction is even more likely to occur when
enlarging already existing holes and at the
point when the bit breaks through the other
side of the material.
8
9
Shifting Speeds (Fig. 8)
Drilling
MAINTENANCE
Cat. No. 1675-1 has
Before drilling, clamp down the material
securely. A poorly secured piece of material
may result in personal injury or inaccurate
drilling. When drilling in light gauge metal or
wood, use a wooden block to back up the ma-
terial to prevent damage to the workpiece.
Fig. 8
a gear shift lever on
the right side of the
gear case.
WARNING
WARNING
The high setting
(1200 RPM HI) is
the low torque setting
and is designed for
driving Selfeed bits
1-3/8" in diameter
and smaller.
Toreducetheriskofinjury,alwaysun-
plugyourtoolbeforeperformingany
maintenance.Neverdisassemblethe
tool or try to do any rewiring on the
tool's electrical system. Contact a
MILWAUKEE service facility for ALL
repairs.
To reduce the risk of injury, electric
shock and damage to the tool, never
immerse your tool in liquid or allow a
liquid to flow inside the tool.
Mark the center of the hole to be drilled with
a center punch to give the bit a start and to
prevent it from "walking." Lubricate the drill
bit with cutting oil when drilling iron or steel.
Use a coolant when drilling nonferrous met-
als such as copper, brass or aluminum.
Cleaning
The low setting (300
RPM LO) is the high
torque setting and is
designed for driving
Selfeed bits 1-1/2" in
diameter and larger.
Clean dust and debris from vents. Keep
the tool handles clean, dry and free of oil
or grease. Use only mild soap and a damp
cloth to clean your tool since certain cleaning
agents and solvents are harmful to plastics
and other insulated parts. Some of these
include: gasoline, turpentine, lacquer thinner,
paint thinner, chlorinated cleaning solvents,
ammonia and household detergents con-
taining ammonia. Never use flammable or
combustible solvents around tools.
Maintaining Tools
To start a selfeed bit, run the threaded feed
screw into the work by flicking the trigger
switch, permitting the bit to coast until the
teeth contact the work surface. Align the bit
properly before proceeding. This will reduce
cocking and jamming when starting. To re-
duce jamming on breakthrough, decrease
the drilling pressure when the feed screw
point breaks through the workpiece. Proceed
with steady, even pressure.
Keep your tool in good repair by adopting a
regular maintenance program. Before use,
examine the general condition of your tool.
Inspect guards, switches, tool cord set and
extension cord for damage. Check for loose
screws, misalignment, binding of moving
parts, improper mounting, broken parts and
any other condition that may affect its safe
operation. If abnormal noise or vibration oc-
curs, turn the tool off immediately and have
the problem corrected before further use.
Do not use a damaged tool. Tag damaged
tools “DO NOT USE” until repaired (see
“Repairs”).
Reversing (Fig. 9)
Fig. 9
Repairs
WARNING
If your tool is damaged, return the entire tool
to the nearest service center.
To reduce the risk of injury, always
wear eye protection.
Under normal conditions, relubrication is not
necessary until the motor brushes need to
be replaced. After six months to one year,
depending on use, return your tool to the
nearest MILWAUKEE service facility for the
following:
Chuck Removal
To remove the chuck from the drill:
1. Unplug tool.
•
•
•
Lubrication
A reversing switch is located below the trig-
ger switch for removal of bits from holes.
Permit the motor to come to a complete stop
before reversing. Reversing the tool with the
gears in motion may cause severe damage.
When removing selfeed bits from partially
drilled holes, a flick of the trigger switch
will free the threaded pilot screw. When the
threads are loose, lift the bit from the work-
piece with the motor stopped.
2. Fully open the chuck jaws
Brush inspection and replacement
3. Remove the left-handed thread screw
from inside the chuck by turning it clock-
wise.
Mechanical inspection and cleaning
(gears, spindles, bearings, housing,
etc.)
4. Pull the chuck off of the spindle.
•
•
Electrical inspection (switch, cord,
armature, etc.)
NOTE: If the chuck does not pull off of
the spindle easily, tap the side of the
chuck with a hammer to loosen it. If this
doesn't work, contact a MILWAUKEE
service center.
Testing to assure proper mechanical and
electrical operation
10
11
RÈGLES GÉNÉRALES DE SÉCURITÉ POUR LES OUTILS
ALIMENTÉS PAR BATTERIE
FIVE YEAR TOOL
LIMITED WARRANTY
ACCESSORIES
WARNING
Every MILWAUKEE tool is tested before
leaving the factory and is warranted to be
free from defects in material and workman-
ship. MILWAUKEE will repair or replace (at
MILWAUKEE’s discretion), without charge,
any tool (including battery chargers) which
examination proves to be defective in ma-
terial or workmanship from five (5) years
after the date of purchase. Return the tool
and a copy of the purchase receipt or other
proof of purchase to a MILWAUKEE Factory
Service/Sales Support Branch location or
MILWAUKEE Authorized Service Station,
freight prepaid and insured. This warranty
does not cover damage from repairs made
or attempted by other than MILWAUKEE au-
thorized personnel, abuse, normal wear and
tear, lack of maintenance, or accidents.
AVERTISSEMENT
To reduce the risk of injury, always
unplug the tool before attaching or
removing accessories. Use only spe-
cifically recommended accessories.
Others may be hazardous.
LIRE SOIGNEUSEMENT TOUTES LES INSTRUCTIONS
Le non respect des instructions ci-après peut entraîner des chocs électriques, des
incendies et/ou des blessures graves. Le terme «outil électrique» figurant dans les
avertissements ci-dessous renvoie à l’outil électrique à alimentation par le réseau
(à cordon) ou par batterie (sans fil).
For a complete listing of accessories refer to
your MILWAUKEE Electric Tool catalog or go
a catalog, contact your local distributor or a
service center.
CONSERVER CES INSTRUCTIONS
7. Prendre soin du cordon. Ne jamais
SÉCURITÉ DU LIEU
utiliser le cordon pour transporter,
tirer ou débrancher l’outil électrique.
Tenir le cordon à l’écart de la chaleur,
DE TRAVAIL
Plastic Carrying Case
1. Maintenirlazonedetravailpropreetbien
éclairée. Les zones encombrées ou mal
éclairées sont favorables aux accidents.
des huiles, des arêtes coupantes ou
des pièces en mouvement. Un cordon
endommagé ou emmêlé présente un
risque accru de choc électrique.
Cat. No. 48-55-0111
The warranty period for V28 Battery Packs
is two (2) years from the date of purchase.
The warranty period for Ni-Cd battery Packs,
Flashlights, Radios are warranted for one (1)
year from the date of purchase.
Type "E" Grease
2. Ne pas utiliser d’outil électrique dans
une atmosphère explosive, telle
qu’en en présence de liquides, de
gaz ou de poussières inflammables.
Les outils électriques génèrent des
étincelles qui peuvent enflammer les
poussières ou les fumées.
8. Se procurer un cordon d’alimentation
approprié en cas d’utilisation
d’un outil électrique à l’extérieur.
L’utilisation d’un cordon d’alimentation
pour usage extérieur réduit le risque de
choc électrique.
Cat. No. 49-08-4122
Chuck Key Holder
THE REPAIR AND REPLACEMENT REM-
EDIES DESCRIBED HEREINARE EXCLU-
SIVE. IN NO EVENT SHALL MILWAUKEE
BE LIABLE FOR ANY INCIDENTAL, SPE-
CIAL, OR CONSEQUENTIAL DAMAGES,
INCLUDING LOSS OF PROFITS.
Cat. No. 48-66-4040
3. Tenir les enfants et les personnes
non autorisées à l’écart pendant le
fonctionnement d’un outil électrique.
Unmanqued’attentiondel’opérateurrisque
de lui faire perdre le contrôle de l’outil.
Chuck Key
SÉCURITÉ INDIVIDUELLE
Cat. No. 48-66-3280
9. Être sur ses gardes, être attentif et
faire preuve de bon sens en utilisant
un outil électrique. Ne pas utiliser
un outil électrique en cas de fatigue
ou sous l’influence de drogues,
d’alcool ou de médicaments. Un
instant d’inattention lors de l’utilisation
d’un outil électrique peut entraîner des
blessures graves.
THIS WARRANTY IS EXCLUSIVE AND IN
LIEU OF ALL OTHER WARRANTIES, OR
CONDITIONS, WRITTEN OR ORAL, EX-
PRESSED OR IMPLIED FOR MERCHANT-
ABLILITY OR FITNESS FOR PARTICULAR
USE OR PURPOSE.
SÉCURITÉ ÉLECTRIQUE
4. La fiche de l’outil électrique doit cor-
respondre à la prise d’alimentation.
Ne jamais modifier la fiche d’une
manière quelconque. Ne pas utiliser
d’adaptateur avec les outils élec-
triques mis à la terre (à la masse).
Des fiches non modifiées et des prises
d’alimentation assorties réduisent le
risque de choc électrique.
This warranty gives you specific legal rights.
You may also have other rights that vary from
state to state and province to province. In
those states that do not allow the exclusion of
implied warranties or limitation of incidental
or consequential damages, the above limi-
tations or exclusions may not apply to you.
This warranty applies to the United States,
Canada, and Mexico only.
10. Utiliser un équipement de sécurité.
Toujours porter des lunettes de pro-
tection. Un équipement de sécurité
comprenant masque anti-poussière,
chaussures de sécurité anti-dérapantes,
casque ou dispositif de protection anti-
bruit peut, dans les circonstances appro-
priées, réduire le risque de blessure.
5. Éviter tout contact corporel avec des
surfaces reliées à la masse ou à la
terre telles que tuyaux, radiateurs,
cuisinières et réfrigérateurs. Un risque
de choc électrique plus élevé existe si le
corps est relié à la masse ou à la terre.
11. Éviter tout démarrage accidentel de
l’outil. S’assurer que le commutateur
est en position OFF (Arrêt) avant de
brancher l’outil. Le port de l’outil avec
un doigt sur le commutateur ou son
branchement avec le commutateur en
position ON (Marche) sont favorables
aux accidents.
6. Ne pas exposer les outils électriques
à la pluie ou à l’humidité. Le risque de
choc électrique augmente si de l’eau
s’infiltre dans un outil électrique.
12
13
|