Instructions for Econo Plus Feeder Kit
THANK YOU for your purchase of the Econo Plus Feeder Kit.
Please read this sheet before operating the unit. If you should have
any questions about this product or any other Moultrie product,
please contact us using the information below. To help us to better
serve you, please complete and mail the enclosed Warranty Card.
DRILLING YOUR DRUM/BARREL/BUCKET
Funnel Holes
Econo Plus Feeder will mount to the bottom of any drum or bucket
caution: wear eye protection
Turn drum over, measure and mark the center of the bottom.
Center the template on the bottom of the drum and secure
with tape. Drill two 3/16" Funnel holes and three 5/16"
Feeder Leg holes.
Feeder Leg Holes
Bolts
Using a Hole Saw, drill a 2-1/4" hole in the center of the
bottom of your drum.
MOUNTING THE FEEDER
Short
Bolts
Place Funnel inside Drum with
small end of funnel facing down,
and attach with two Short Bolts
using nuts and washers provided.
Drum
Turn Drum upside down.
Funnel
Feeder
Place Feeder on Drum.
Attach Feeder Legs to Drum as
Feeder Legs
shown with Long Bolts using
nuts and washers provided.
Long
Bolts
Drum
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver
•
•
Instructions for 30 Gallon Hanging Feeder
THANK YOU for your purchase of the Hanging Feeder, a
top quality Moultrie product. Please read this sheet before
operating this unit. If you should have any questions about
this or any other Moultrie product, please contact us using
the information at bottom of page.
To help us better serve you, please complete and mail the
enclosed Warranty Card.
MOUNT YOUR FEEDER KIT TO DRUM
Using instructions provided with your Feeder Kit, mount your feeder and
small funnel to the bottom of the Drum.
INSTALL OPTIONAL LARGE FUNNEL
If you will be using an optional 30 gallon internal funnel (#MFH-FUN30),
install per the instructions provided with funnel.
INSTALL HANGING BRACKET
Insert steel rod with Coupler
Nuts in Drum. With Nuts and
Washers on outside of drum,
Tighten eye bolts into Coupler
Nuts.
Drum
Steel Rod with
Coupler Nuts
Nut and
Washer
Eyebolt
TIPS AND POINTERS
1: (Q) When should I fill the drum on my feeder? (A) To prevent damage to the feeder, do not
load drum until unit is off the ground.
2: (Q) This is going to be heavy. How should I hang it? (A) A 30 gallon drum can hold up to 200
lbs. of feed; we suggest using block and tackle to raise to desired height, then secure as required.
3: (Q) What should I hang it with and how high should I hang it? (A) Some animals will chew
through products like rope, so chain or steel cable is best. The bottom of the feeder should be
about 7 feet from the ground.
Our Service Department will gladly answer any questions you have.
Call 205-664-6700 Monday –ꢀFriday, 8:00 AM to 5:00 PM CST.
061604R10 / MFH-MH
|