AMS35i
ANTONY MICHAELSON SIGNATURE
PURE CLASS A 35W INTEGRATED AMPLIFIER
INSTRUCTIONS FOR USE
Thank you for purchasing the Musical Fidelity AMS35i pure class A Integrated amplifier.
The AMS35i Integrated uses a pure class A output stage to deliver the absolute best in audio
quality with no listener fatigue and freedom from crossover distortion artefacts. This results in an
astounding improvement in musicality and tonal neutrality. It also features a fully balanced input
for the best in sound quality and dynamics.
The AMS35i is designed to be partnered with present and future AMS series products. This
combination yields one of the best high-fidelity systems available at any price.
Used properly and carefully, it should give many years of outstanding musical reproduction.
Dust regularly with a soft duster or soft brush, but be careful when using cleaning or polishing agents
- they may harm the surface finish.
If there are any questions about the audio system,
please consult the dealer who is there to help and advise.
SAFETY INFORMATION
AMS35i
IMPORTANT! (U.K. only)
This unit is supplied in the U.K. with mains lead fitted with a moulded 13 amp plug. If, for any reason, it is necessary
to remove the plug, please remove the fuse holder and dispose of the plug safely, out of reach of children.
It must not be plugged into a mains outlet.
The wires in the mains lead supplied with this appliance are coloured in accordance with the following code:
Green and yellow..............Earth
Blue................................Neutral
Brown.................................Live
WARNING - This appliance MUST be earthed
As the colours of the wires of the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in the plug, proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the
letter E or coloured green or green-and-yellow, or by the earth symbol :
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
If connecting to a BS1363 plug, a 13 amp fuse must be used.
WARNING:
ANY MODIFICATIONS TO THIS PRODUCT NOT EXPRESSLY APPROVED
BY MUSICAL FIDELITY WHO IS THE PARTY RESPONSIBLE FOR
STANDARDS COMPLIANCE COULD VOID THE USER'S AUTHORITY TO
OPERATE THIS EQUIPMENT.
Issue 2
Page 3 of 12
GENERAL ADVICE
AMS35i
INSTALLATION PRECAUTIONS & USER INFORMATION
This new AMS35i is designed and built to provide trouble-free performance, but as with all electronic devices it is
necessary to observe a few precautions:
Heed all warnings shown on the back of the product.
Only connect the AMS35i to a mains outlet having the same voltage as marked at the back of the unit.
Always ensure that when disconnecting and reconnecting your audio equipment the mains supply is switched
off.
Position the mains lead and signal interconnects where they are not likely to be walked on or trapped by items
placed on them.
Do not use near water, or place water-filled containers on the AMS35i, for example, a flower vase or potted
plants. If water does spill inside, immediately pull out the mains plug from the wall socket and inform
your dealer, who should then check the unit before further use. Entry of liquid into the AMS35i is
dangerous, and may cause electric shock or fire hazard.
Do not place the unit near direct heat sources such as radiators, direct sunlight or other equipment.
Do not remove any covers or try to gain access to the inside. There are no internal adjustments or fuses you
can replace yourself. Refer all service work to an authorised Musical Fidelity agent.
Note: Unauthorised opening of the equipment will invalidate any warranty claim.
Dust regularly with a soft cloth or soft brush but be careful when using cleaning or polishing agents - they may
harm the surface finish.
The electronics in modern hi-fi equipment is complex and may, therefore, be adversely affected or damaged by
lightning. For protection of the audio system during electrical storms, remove the mains plugs and disconnect any
aerial lead.
If after-sales service is required, to help the dealer identify the AMS35i please quote the serial number located on the
rear panel of the unit.
Issue 2
Page 4 of 12
ITEM DISPOSAL INFORMATION
AMS35i
DISPOSAL
AFVAL
The crossed out wheeled bin label that appears on the
back panel of the product indicates that the product must not be
disposed of as normal household waste. To prevent possible harm
to the environment please separate the product from other waste to
ensure that it can be recycled in an environmentally safe manner.
Please contact local government office or retailer for available
collection facilities.
Het label op de achterzijde van dit apparaat, een
afvalbak op wielen met een kruis doorgehaald, geeft aan dat dit
apparaat niet samen met gewoon huishoudafval mag worden
weggegooid. Om mogelijke schade aan onze leefomgeving te
voorkomen dient dit apparaat, gescheiden van gewoon
huishoudelijk afval, te worden afgevoerd zodat het op een
milieuvriendelijke manier kan worden gerecycled. Neem voor
beschikbare inzamelplaatsen contact op met uw gemeentelijke
reinigingsdienst of met uw elektronica leverancier.
DISPOSITION
La poubelle sur roulettes barrées X, qui apparaît en logo
sur le panneau arrière du produit, indique que celui-ci ne doit pas
être traité comme un déchet domestique commun. Afin de protéger
l'environnement, ce produit électronique devra être géré
séparément et donc recyclé selon les nouvelles normes
Européennes Rohs concernant les déchets d'appareils électroniques.
Prière de contacter les services concernés gouvernementaux ou
votre point de vente pour l'élimination et l'enlèvement de déchets
électroniques équipés de composants électroniques.
HÄVITTÄMINEN
Yliruksattua jäteastiaa kuvaava tarra tuotteen
takalevyssä kertoo, että tuotetta ei saa käsitellä normaalina
talousjätteenä. Ympäristön suojelemiseksi on tuote pidettävä
erillään muusta jätteestä ja se on kierrätettävä ekologisesti
kestävällä tavalla. Ota yhteyttä laitteen myyjään tai Pirkanmaan
Ympäristökeskukseen lähimmän kierrätyskeskuksen löytämiseksi.
AFSKAFNING
DISPOSAL
Logoet med en skraldespand med kryds over på bagsiden
af apparatet indikerer at dette produkt ikke må kasseres som normal
husholdningsaffald. For at forebygge mulig skade på miljøet, bedes
De separere dette produkt fra andet affald, og sikre at det bliver
genbrugt på en miljørigtig måde. Kontakt venligst de lokale
myndigheder eller din forhandler for oplysning om nærmeste
tilgængelige opsamlingssted for elektronikaffald.
La etiqueta cruzada hacia fuera del compartimiento que
aparece en el panel trasero del producto indica que el producto no
se debe reciclarse como basura normal de la casa. Para prevenir
daños posible al ambiente separe por favor el producto de otras
basura para asegurarse de que puede ser reciclada de una manera
ambientalmente segura. Entre en contacto por favor a su oficina
gubernamental local o a su minorista para las instalaciones
disponibles de la colección.
∆ΙΑ∆ΙΚΑΣΙΑ ΑΠΟΡΡΙΨΗΣ
ΤΟ
ΤΡΟΧΗΛΑΤΟ ΚΑ∆Ο ΑΠΟΡΡΙΜΑΤΩΝ ΣΤΗΝ ΠΙΣΩ
ΟΨΗ ΤΟΥ ΜΗΧΑΝΗΜΑΤΟΣ
∆ΗΛΩΝΕΙ ΟΤΙ ΤΟ ΠΡΟΙΟΝ ΑΥΤΟ ∆ΕΝ ΠΡΕΠΕΙ ΝΑ
∆ΙΑΧΕΙΡΙΣΘΕΙ ΣΑΝ ΣΥΝΗΘΙΣΜΕΝΟ ΟΙΚΙΑΚΟ ΑΠΟΒΛΗΤΟ.
ΠΡΟΣ ΑΠΟΦΥΓΗ ΕΝ∆ΕΧΟΜΕΝΗΣ ΕΠΙΒΑΡΥΝΣΗΣ ΤΟΥ
ΠΕΡΙΒΑΛΛΟΝΤΟΣ, ΞΕΧΩΡΙΣΤΕ ΤΟ ΠΡΟΙΟΝ ΑΠΟ ΤΑ
ΑΛΛΑ
ΣΗΜΑ
ΜΕ
ΤΟΝ
∆ΙΑΓΕΓΡΑΜΜΕΝΟ
RIFIUTI
L'etichetta del cassonetto barrato riportato sul retro
dell'apparecchio indica che il prodotto non deve essere smaltito
tramite la procedura normale di smaltimento dei rifiuti domestici.
Per evitare eventuali danni all'ambiente, separare questo prodotto
da altri rifiuti domestici in modo che possa venire riciclato in base
alle procedure di rispetto ambientale. Per maggiori dettagli
sulle aree di raccolta disponibili, contattate l'ufficio govenativo
locale od il rivenditore del prodotto.
ΑΠΟΡΡΙΜΑΤΑ ΩΣΤΕ ΝΑ ΕΞΑΣΦΑΛΙΣΘΕΙ Η ΑΝΑΚΥΚΛΩΣΗ
ΤΟΥ ΜΕ ΤΟΝ ΠΡΕΠΟΝΤΑ ΤΡΟΠΟ.
ΠΑΡΑΚΑΛΟΥΜΕ ΝΑ ΕΠΙΚΟΙΝΩΝΗΣΕΤΕ ΜΕ ΤΗΝ ΤΟΠΙΚΗ
FACHGERECHTE ENTSORGUNG:
ΥΠΗΡΕΣΙΑ ΑΝΑΚΥΚΛΩΣΗΣ
Η
ΜΕ ΤΟ ΚΑΤΑΣΤΗΜΑ
Das auf der Geräterückseite angebrachte Label deutet
darauf hin, dass das Produkt nicht mit konventionellem
Hauskehricht entsorgt werden darf. Um Schäden und
Verschmutzungen an Umwelt und Mensch zu vermeiden, muss das
Produkt fachgerecht entsorgt und von anderem Abfall getrennt
werden. Wenden Sie sich bei Fragen hierzu an Ihren Fachhändler
oder an eine öffentliche Informationsstelle.
ΑΓΟΡΑΣ ΓΙΑ ΠΕΡΙΣΣΟΤΕΡΕΣ ΛΕΠΤΟΜΕΡΕΙΕΣ.
Issue 2
Page 5 of 12
INSTALLATION
AMS35i
INTRODUCTION
POWER CONNECTIONS
Congratulations on the purchase of the new AMS35i Class A
Integrated amplifier. Great attention has been paid to internal
layout, isolating each circuit section to prevent possible
interaction.
The AMS35i is supplied with a standard IEC mains cable
which plugs into the IEC socket at the back of the unit (see
P.7)
The unit features a finely tuned and tweaked , for smooth
sound coupled with low noise and virtually no distortion.
The power amplifier consists of two monoblock class-A
amplifier modules with separate supplies for the absolute best
in separation and imaging. Generously rated, they are enough
to drive even the most demanding loudspeakers with ease.
Low distortion and very quiet they will deliver all music types
exactly as the artist originally intended.
The resultant performance achieved by this unit is among the
best in the world. It has excellent signal to noise ratio, low
distortion, wide bandwidth and dynamic range, with
extraordinary resolution and fine detail.
AUDIO CONNECTIONS
RCA Inputs: Connect all RCA single-ended sources to
relevant analogue inputs (see p.7 For more information). Use
good quality fully connected (signal and ground) coaxial
phono cables for all RCA signal connections.
XLR Inputs: Connect all XLR balanced sources to relevant
analogue inputs (see p.7 For more information). Use good
quality fully connected (signals and ground) balanced XLR
cables for all XLR signal connections.
Outputs: Connect loudspeakers to the terminals on the back
panel marked as LEFT and RIGHT SPEAKER outputs
CLEANING
Before cleaning the unit, switch off power at the mains switch
and remove the mains plug from the wall socket.
Clean the cabinet and remote control unit using a moist cloth.
Using solvents, white spirit or thinners is not advised, as they
could damage the surface finish.
The TAPE output allows loop through of analogue signals
for example, to pass on to recorder or monitor. It is also the
ideal output to connect our headphone amps into.
The PRE-OUT output allows analogue signals controlled by
the volume, to pass on to a second amplifier. This is useful
for bi-amping.
INSTALLATION
Position the AMS35i on a stable, horizontal surface where
there is no risk of it being knocked, or subjected to vibration
such as from loudspeakers.
Important note:
As a “CLASS A” amplifier, the unit dissipates a quantity of
power at all times, and it is important that it is adequately
ventilated. The top and bottom are perforated to allow the
smooth flow of heat through the unit. It is therefore not
recommended that the unit is enclosed in a cabinet or placed
where the ventilation holes are impeded as this could result in
the unit cutting out due to excessive heat build-up.
The AMS35i must be protected from humidity - if the unit is
moved from a cold place to a warm room, leave the unit for an
hour or so to allow sufficient time for the moisture to
evaporate.
Issue 2
Page 6 of 12
FACILITIES & CONNECTIONS
AMS35i
FRONT PANEL
1
2
3
4
5
1. ON/OFF Button
4. VOLUME control
2. IR RECIEVER lens
3. TAPE MONITOR button
5. ANALOGUE INPUT source selector buttons
REAR PANEL
6
7
8
9
10
11
6. LOUDSPEAKER OUTPUT Right
7. BALANCED XLR right and left inputs
9. PRE, TAPE OUTPUT RCA sockets
10. IEC MAINS INPUT
8. CD, TUNER, AUX/HT, TAPE INPUT RCA
11. LOUDSPEAKER OUTPUT Left
Sockets
Issue 2
Page 7 of 12
REMOTE CONTROL
AMS35i
Remote control Handset (supplied with the battery already installed).
The AMS35i remote control shown below enables functions from this unit to be operated from a convenient distance.
Equivalent buttons on the remote control have the same functions as those on the front panel of the unit. Other
functions are only available by remote control.
As the handset uses an invisible infra-red light beam, the front edge must be pointed directly towards the receiver
window at the front of the player, without visual obstruction between them.
For reliable remote control operation, the AMS35i should also be positioned so that direct sunlight, fluorescent or
other bright lights do not fall directly on the IR receiver lens (see P.7). Such light can interfere with remote control
operation and/ or maximum operating range.
If the range of the remote control greatly decreases, replace the battery, VARTA Lithium Li-Mn button type CR2450.
Please dispose of used batteries in accordance to local regulations.
Changing the Battery
If the remote fails to operate the AMS35i
functions correctly, or
a
substantial
reduction in range is observed, the
battery may be exhausted.
1. Remove the six screws in the base of
the remote control.
MUTE – Mutes outputs
until pressed again
VOLUME ▲ – increases
volume
VOLUME ▼ – decreases
volume
2. Remove the base to gain access to the
battery holder in the bottom of the
remote.
3. Gently Lift the spent battery from the
holder.
4. Discard the spent battery according to
local disposal regulations.
5. Replace with a new VARTA CR2450
Li-Mn battery. We do not recommend
any other battery type.
TAPE MONITOR –
Selects tape input for
monitoring
If there are any problems with changing
the battery please contact the dealer for
assistance.
BALANCED INPUT-
Selects BALANCED input
CD – Selects CD input
RC5 codes used by this component
TUNER – Selects TUNER
input
AUX – Selects AUX input
HEX
10
DECIMAL
16
SYSTEM
CODE FOR
AMPLIFIER
MUTE
VOLUME ▲
VOLUME ▼
BAL. INPUT
CD
TUNER
AUX
TAPE
TAPE MON.
TAPE – Select TAPE input
0D
10
11
01
02
03
04
05
14
13
16
17
1
2
3
4
5
20
Important notice- The remote control supplied is expensively machined from solid aluminium.
Please take great care of this remote control as it would be costly to replace.
Issue 2
Page 8 of 12
AMPLIFIER OPERATION
AMS35i
STARTING
TAPE
Once all connections are made, switch on the unit, using
the POWER button front of the unit. The MUTE LED
will light. Speaker outputs are muted for about 15
seconds, so no sound will be heard from the speakers.
Once the 15 seconds is up the MUTE LED goes out,
indicating unit is settled, and ready for use.
To use the TAPE input, connect external source to the
TAPE input (see p.7). Select TAPE input by pressing
the source up/down buttons until TAPE LED is lit.
Selecting the TAPE input can also be achieved by
pressing the corresponding button on the remote handset
(see p. 8).
VOLUME
RECORDING AND TAPE MONITOR
The volume should be adjusted for normal listening
levels. This is done by turning the volume up/down
knob on the front panel. Adjusting the volume can also
be achieved using the remote handset, using the volume
up/down buttons (see p. 9).
To record to tape, (or alternatively CD recorder, DAT,
minidisk or computer soundcard analogue input) connect
the tape out to the tape recorder line in. Press the input
selector button on the front panel or remote control. This
source will now be routed to the AMS35i TAPE OUT
for recording by tape deck.
MUTE (remote only)
The recording can be directly monitored through the
loudspeakers by pressing the TAPE MONITOR button.
Press again to return back to the input being recorded.
On some 3 head tape decks there is an additional
tape/source switch which should be in the tape position
for this to work. If in doubt, please consult tape deck
operating manual.
The sound from the speakers may be muted by use of
the MUTE button on the remote. Press once, and
MUTE LED will light indicating muted state. No sound
will be heard from the speakers.
To return to listening; simply press the MUTE button
again so MUTE LED is no longer lit.
Note - adjustment of the volume control has no effect on
the recording level.
BALACED INPUT
To use the balanced input, connect balanced source
outputs to the balanced input XLR sockets (see p.7).
Select BALANCED input by pressing the
BALANCED INPUT button so BALANCED INPUT
LED is lit.
Selecting the BALANCED input can also be achieved
by pressing the corresponding button on the remote
handset, (see p. 8).
CD
To use the CD input, connect CD player outputs to the
CD input RCA sockets (see p.7). Select CD input by
pressing the CD button so CD LED is lit.
Selecting the CD input can also be achieved by
pressing the corresponding button on the remote
handset, (see p. 8).
TUNER
To use the tuner input, connect tuner outputs to the tuner
input RCA sockets (see p.7). Select TUNER input by
pressing the TUNER button so TUNER LED is lit.
Selecting the TUNER input can also be achieved by
pressing the corresponding button on the remote
handset, (see p. 8).
AUX
To use the tuner input, connect tuner outputs to the
tuner input RCA sockets (see p.7). Select AUX input by
pressing the AUX button so AUX LED is lit.
Selecting the AUX input can also be achieved by
pressing the corresponding button on the remote
handset, (see p. 8).
Issue 2
Page 9 of 12
AMPLIFIER PROBLEMS?
AMS35i
Basic problem-solving with an amplifier is similar to troubleshooting other electrical or electronic equipment. Always check the most obvious
possible causes first, such as the following examples:
Problem
Probable Cause
Remedy
No power when POWER button is pressed
Mains power plug is not fully inserted into
rear socket
Plug in securely.
No sound
Sound cut
Mute function is still active
Press the MUTE button on the remote control
to cancel.
Check audio input lead connections
Wrong connections between input sources and
the unit
Speakers not connected, or incorrectly wired
Check speaker cables
Loose connection
Check speaker and input connections
Output overload or short circuit
Switch unit off. Check speaker connections
for shorting strands or wires. When all has
been double-checked reduce volume and
switch unit back on.
N.B. Take great care when bi-wiring or bi-
amping that speaker bass and treble linking
straps are removed; see speaker manual for
more information
Sound is not precise, lacking in bass and
stereo image
Speakers are connected out of phase, i.e.,
connections to one speaker (+ and -) are
reversed
Ensure speakers are connected with same
polarity at amplifier and speaker ends.
Hum
Audio connector plug not fully pushed in
Cable Fault
Insert plug securely
Check cable is connected at both ends.
Unsuitable Cable
N.B. Some esoteric cables have internal
wiring intentionally disconnected/modified.
For best results on all inputs analogue AND
digital, please use good quality screened coax;
signal and screens both separately connected
at both ends.
(e.g. cable grounds not connected)
No audio output, or too low level output
Remote control does not work
Incorrect or missing connections
Check connections and make sure they are
secure.
Amplifier’s POWER switch is set to off
Set switch to on
Unit overheated
Check for excessive heat build-up.
Insert batteries correctly
One or more batteries fitted the wrong way
round
Change batteries for a new set
Ensure there is no obstruction between the
Batteries are flat
Remote control is not pointed directly towards remote control and amplifier front.
the front panel of the amplifier
Lighting such as fluorescent, incandescent, or
Interference from another source
even sunlight contains large amounts of infra
red radiation. Ensure such sources are not
shining directly on the infra red window as
this could swamp the signal from the remote
control.
Also check the system and any other nearby
remotes for stuck buttons
Remote control range has greatly reduced
Batteries are running out
Change batteries for a new set.
If none of these actions affect a cure, please contact the dealer, or an authorised Musical Fidelity service agent. Remember; never open the case
of the AMS35i, as this will invalidate the guarantee.
Issue 2
Page 10 of 12
AMPLIFIER SPECIFICATIONS
AMS35i
Output:
Power
35 Watts per channel into 8 Ohms (15.5dBW),
Voltage
Voltage
Current peak-to-peak
Damping factor
Output devices
17 Volts RMS 20Hz to 20 kHz
47 Volts Peak-to-peak
20 Amps
130
2 pairs per channel
Balanced Line input:
THD+N
< 0.014% unwtd, 20Hz to 20 kHz
> 96dB ‘A’-weighted
40k Ohms
Signal / noise ratio
Input impedance
Frequency response
10Hz to 50 kHz, +0, -1dB
Connections:
Line level inputs
Line level outputs
Speaker outputs
1 pairs line level XLR (balanced) connectors
4 pairs line level RCA connectors
1 pair line level RCA connectors, constant level TAPE outputs
1 pair line level RCA connectors, preamp outputs for e.g. biamping
2 pairs 4mm banana plug/binding posts
Power requirement:
Mains voltages:
115/230VAC 50/60Hz (factory pre-set)
100VAC 50/60Hz (alternative)
330 Watts continuous
Consumption:
Weight:
28.3kg
33kg
62⅓lbs
72⅔ lbs
unit only, unboxed
in shipping carton
Dimensions: 483mm,
148mm,
19”
5⅞”
18¾”
wide
high including feet
deep (front to back) including terminals
475mm,
Standard accessories:
IEC type mains lead (10-Amp type),
AMS35i remote control
Varta CR2450 Li-Mn battery
Musical Fidelity reserves the right to make
improvements which may result in specification or
feature changes without notice.
Issue 2
Page 11 of 12
MANUAL REVISION
AMS35i
RELEASE
DATE
CHANGES
Issue 1
Issue 2
03/07/09
10/07/09
1st issue.
Remote control page
updated
Issue 2
Page 12 of 12
|