2. THEN, INSTALL THE TA612V VOICE ADAPTER
3. SET UP AN ACCOUNT AT BBPGLOBAL
Smart Internet Phone Adapter
a) Power up the computer.
a. Plug the power cable into the TA612V Power port, and plug the other end
into an electrical outlet. This turns on your TA612V Smart Internet Phone
Adaptor. You do not need to unplug it when not in use.
TA612V
b) Use a Web browser to go to the bbpglobal web site,
Follow the instructions to setup your account. During this process,
you will be asked to provide your contact information, the serial
number and the MAC address of your TA612V, shown at the back
of your unit.
b. Check that the Power light
illuminated. Wait at least five minutes for the phone adapter to start up.
on the Smart Internet Phone Adaptor is
BBPGlobal
c) Reboot your TA612V after registration.
Add voice to your internet
d) After reboot, pick up your telephone handset and listen for a dial
tone. If you hear dial tone then you have finished installation and
may begin making calls. For dialing instructions, see the Helpfule
Hints on this card. If you do not hear a dial tone, see
Troubleshooting. For more tips about troubleshooting, see the
User Manual.
Internet
PC
Restore
Factory
Settings
12VDC, 1.2A
Power
Phone 2 Phone 1
e) (Optional) You may also select a PSTN number to receive phone
calls. Please go to the following web site to select a PSTN number.
Please note there is an additional charge for this service.
INSTALLATION GUIDE
There may be updates that need to be downloaded such as new
firmware or changer to your features. Do not interrupt the
registration process by unplugging the power or lifting the
receiver on your phone during the start-up process. Interruption
of the startup may result in interruption of service.
MINIMUM SYSTEM REQUIREMENTS
Before installing the NETGEAR TA612V Smart Internet Phone Adaptor,
please make sure that your computer system has the following:
HELPFUL HINTS
•
•
Broadband Internet connection via cable or DSL modem.
Home analogue telephone with a single line.
•
If you experience any problems concerning the BBPGlobal service
please contact our customer service on 1300 663 723 during office
hours or send us an email to [email protected]
c. The status light on the front of the TA612V will flash.
Wait five minutes before continuing.
•
To manage your bbpglobal account online, go to
Blink=Activity
Ethernet: Green=100Mbps/Amber=10Mbps
and follow the BBPGlobal Login link. You can:
SINGLE USER INSTALLATION
•
•
•
•
•
•
Listen to voice mail online
1. SET UP THE NETWORK CONNECTIONS
Forward your voice messages to email
Check call details and account balance
Recharge online
a. Unplug the power cable for your modem. Make sure that you have
turned your computer off and that you DO NOT plug in the
TA612V Smart Internet Phone Adaptor until instructed to do so.
Phone 2
Phone 1
Internet
Transfer credits to other bbpglobal accounts
b. Disconnect the Ethernet cable from the back of your PC and then
plug it into the Internet Port on the TA612V
Power
For further information regarding the use of BBPGlobal service, visit:
PC
Status
c. Connect one end of the Ethernet cable we provide into the PC port
on the TA612V. Connect the other end of this Ethernet cable into
the Ethernet port on the computer.
•
The LEDs for the Phone 1 and Phone 2 ports work as shown below:
Amber On:
The phone is off the hook
d. If you have a DSL modem that requires PPPoE you need to set up your
PPPoE http://192.168.61.1/
Amber Fast Blink: Not ready, registering to server.
Green On:
Green Blink:
Off:
Ready to use.
The phone is connected.
The port is disabled or the power is off.
d. Connect a telephone to the TA612V Phone 1 port.
Log in using the username and password printed on the back of the TA612V.
After setup reboot your TA612V.
e. Power on the modem. Wait about two minutes for it to start up.
|