Technical Support
PLEASE REFER TO THE SUPPORT INFORMATION CARD THAT SHIPPED WITH
YOUR PRODUCT.
expert technical support and timely notices of product and software upgrades.
Fast Ethernet Switch
10/100 Mbps FS605 v3 / FS608 v3
NETGEAR, INC.
Support Information
Phone: 1-888-NETGEAR (For US & Canada only) - 24 x7 phone support
See Support Information card for other countries.
E-mail: [email protected] (24 x 7 online support)
© 2006 NETGEAR, Inc. NETGEAR, the Netgear logo, The Gear Guy, Auto Uplink and
Everybody's Connecting are trademarks or registered trademarks of Netgear, Inc. in the
United States and/or other countries. Microsoft and Windows are registered trademarks of
Microsoft Corporation in the United States and/or other countries. Other brand and product
names are trademarks or registered trademarks of their respective holders. Information is
subject to change without notice. All rights reserved
Installation Guide
February 2006
2 0 1 - 1 0 7 4 9 - 0 1
Unpack the Box and Verify the
Contents
Prepare to Install the Switch
1
2
Decide where you want to place the switch. Find a flat horizontal surface — such as a table,
desk or shelf.
Fast Ethernet Switch FS605 v3/FS608 v3
Make sure the selected location is:
•
•
Not in direct sunlight or near a heater or heating vent.
Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all
sides of the switch.
Stand
•
Well ventilated (especially if it is in a closet).
Also, you’ll need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each device
you want to connect to the switch. Each Ethernet cable must be less than 328 feet (100 meters).
Installation guide,
warranty/registration card
and support
Power adapter
information card
When you open the box, verify that you received everything. The package includes:
•
•
•
•
•
5/8-Port Fast Ethernet Switch FS605 v3/FS608 v3
AC power adapter
FS605 v3/FS608 v3 Installation Guide (this document)
Warranty and support information card
Vertical stand
If you don’t have everything listed above, see the support information card for contact
information. If you’re missing the Technical Support information card itself, get contact
Install the Switch and Connect the Other
Devices
Troubleshooting
The Power light is not lit
The switch has no power.
3
•
•
Make sure the power cord is properly connected to the switch.
Make sure the power adapter is properly connected to a functioning power outlet. If it’s in
a power strip, make sure the power strip is turned on. If the socket is controlled by a light
switch, make sure the switch is in the on position.
•
Make sure you are using the NETGEAR power adapter supplied with your switch.
The Port number light is not lit for a connected device or
stays on continuously
There’s a hardware connection problem.
DSL
modem
•
•
•
Make sure the cable connectors are securely plugged in at the switch and the device.
Make sure the connected device is turned on.
If the Ethernet cable is connected to a NIC or other Ethernet adapter, make sure the card
or adapter is installed correctly and is working.
RP614 4-Port Cable / DSL Router
•
Make sure the cable is less than 328 feet (100 meters).
Fast Ethernet Switch FS608 v3
Technical Specifications
Standards Compatibility:
Data Rate:
IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u,100BASE-TX Fast Ethernet
1. Place the switch on a flat surface using either the attached feet or the provided vertical
stand.
IEEE 802.3x Flow Control; compatible with Windows®, Mac® OS, NetWare®, Linux®
100 Mbps with 4B/5B encoding and MLT-3 physical interface for 100BASE-TX
10 or 100 Mbps half-duplex
2. For each device, insert one end of an Ethernet cable into the port in the device and insert
the other end into one of the Ethernet ports on the switch.
Network Interface:
DC Power:
RJ-45 connector for 10BASE-T or 100BASE-TX Ethernet interface
7.5W max and 7.5V @1.0A DC inputt
Physical Dimensions:
FS605 v3 - W: 147mm (5.79") D: 96.7mm (3.81") H: 28.5mm (1.12")
FS608 v3 - W: 171mm (6.73") D: 113.2mm (4.46") H: 28.5mm (1.12")
FS605 v3 - 0.192kg (0.424 lbs); FS608 v3 - 0.278kg (0.614 lbs)
0 to 50˚ C (32 to 122˚ F)
Note: If you have more than 5 or 8 devices to connect to this switch, you must
connect them to a hub or other switch and then connect that hub or switch to this
switch.
Weight:
Operating Temperature:
Operating Humidity:
10% t0 90% relative humidity, non-condensing
Electromagnetic Compliance: CE mark, Commercial; FCC Part 15, Class B; EN 55 022 (CISPR 22) Class B, VCCI
3. Connect the power adapter’s cord into the back of the switch and then plug the adapter
into a power source (such as a wall socket or power strip).
Class B, C-Tick
Safety Agency Approvals for
the Power Adapter:
CE mark, Commercial UL listed (UL 1950), C-Tick
The Power light should light up.
Performance Specifications
Frame Filter Rate:
Frame Forward Rate:
Network Latency:
(using 64-byte packets)
The corresponding port number for each connected and powered device should light
when link (connection), and flash when activity occurs.
14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port
14,800 frames/sec max for 10M port / 148,800 frames/sec max for 100M port
100 Mbps to 100 Mbps: 20 µs max
Note: If any light doesn’t operate as indicated, go to the Troubleshooting section.
Address Database Size:
Addressing:
Queue Buffer:
1024 MAC addresses
48-bit MAC address
64 kilobytes
|