garden speakers
G S S 1 0 I N S T A l l A T I o N G u I d e
choosinG a Location
The location of the subwoofer should be
based on three considerations: sound
coverage, ease of installation, and the
ease of running cable to the installation
location. The large 10” woofer cone will
provide impressive bass performance for
a large area when properly placed.
Depth should be
between 16 - 18”
(40 – 45 cm)
The subwoofer requires a hole with a
width of approximately 14” (36 cm) and a
length of approximately 30” (76 cm). The
depth should be between 16 - 18” (40 –
45 cm). Additionally, burial rated speaker
Length of approximately
Width of approximately
14”(36 cm)
30”(76 cm).
cable must be run from your subwoofer amplifier to the proposed subwoofer
location. Make certain that there are no obstructions in the planned location
or along the proposed wiring location before proceeding. Many states and
municipalities have specific notification requirements before digging. Make sure
to check with your local building authorities as required prior to digging.
Keep in mind when choosing a location that low frequency sounds will permeate
the entire area which means that the subwoofer does not need to be “aimed” or
pointed in any particular direction.
The subwoofer is made of heavy duty uPVC, designed for many years of
rugged outdoor use and will withstand occasional hits from common handheld
landscape tools, but can be damaged by lawn mowers or other motorized
equipment. Placing the subwoofer where it is not likely to be struck by such
equipment will help ensure years of listening enjoyment. This can be easily done
by careful placement of landscaping features around the bass port tube.
Also, please be aware that you can control the bass output by your placement
location. This is called the boundary effect. You will get more bass response
by mounting the GSS10 near a wall or other flat surface. You can increase
the bass output even more by mounting the GSS10 in a corner location. This
kind of placement gives the speaker two boundaries, further reinforcing the
bass sounds. Of course, mounting the subwoofer further away from any other
boundaries will minimize this effect. Landscaping walls or other structures
could be utilized for this purpose. A further consideration is that the closer
the subwoofer is placed to the home, the more chance of unwanted vibration
entering the home when the subwoofer is played at large volumes.
Choose the location carefully prior to digging any holes or running any wires.
Once the location has been chosen and the hole has been prepared, place the
NILES AUDIO – 1-800-BUY-HIFI – 1-760-710-0992
3
subwoofer into the hole and verify that it is horizontal using the bubble level. It is
now time to connect the loudspeaker wires to the subwoofer. Before connecting
any loudspeaker wire, make certain that the subwoofer amplifier is turned OFF.
Connect the loudspeaker wires to the subwoofer, making certain to match polarity
so that the positive lead from the amplifier matches to the positive lead from the
subwoofer and do the same with the negative leads. When connecting the wires,
be sure to use silicone filled wire nuts, or an appropriate water tight connector or
junction box.
Connect the wires to your subwoofer amplifier and turn it on to test the
connection. If the loudspeaker sounds fine, you can now fill in the hole around
the GSS10. Keep in mind that the subwoofer will sound slightly different when
fully installed in the ground than it will in an open air environment. Verify the
satisfactory performance of each loudspeaker before covering any exposed
trenches or conduit used for your wiring.
Before proceeding, turn off the amplifier for safety.
Carefully pack and compress the dirt around the subwoofer making certain not
to damage either the subwoofer or its wiring. The subwoofer should have firm
support on all sides to prevent any settling in the future.
Should you ever need to service your GSS10 subwoofer, you can use the
Niles Logo located on the top cover to determine where the unit is located
underground. The side of the vent cover with the Niles Logo (
where the subwoofer unit is located.
) is the side
PaintinG
The tube and its dome cover can be painted to match any environment. When
painting the GSS10 port tube, be sure not to paint the underside of the dome.
There are special filter screens that should not be painted over on the underside of
the dome. The top and sides can easily be painted with a high quality spray paint.
recommended amPLifier
The GSS10 is a passive subwoofer designed to be used with a subwoofer
amplifier. We recommend the Niles SWA-500M, Part Number FG01361. The
SWA-500M is a high-current design that can power up to 2 GSS10 subwoofers.
WWW.NILESAUDIO.COM
4
sPecifications
Woofer:
10” Mineral-Filled Polypropylene
Recommended Amplifier Power: 50-500 watts
Frequency Response:
Product Weight:
25 Hz to 110 Hz
25 lbs (11.4 kg)
Recommended Burial Depth:
Max SPL:
16-18” (40-45 cm)
110dB
Impedance:
Temperature Extremes:
8 ohm nominal, 6 ohm minimum
-50F to 185F (-45° to 85° Celsius)
NILES AUDIO – 1-800-BUY-HIFI – 1-760-710-0992
5
notes
WWW.NILESAUDIO.COM
6
BY PHONE (IN USA)
1-800-BUY-HIFI (289-4434)
BY PHONE (OUtSIdE USA)
1-760-710-0992
CUStOmEr SErvICE HOUrS
8:00 AM to 5:30 PM PT
tECHNICAl SUPPOrt HOUrS
6:00 AM to 4:00 PM PT
ON tHE wEB
www.nilesaudio.com
EmAIl tECHNICAl SUPPOrt
EmAIl fOr PrOdUCt SUggEStIONS
NILES AUDIO – 1-800-BUY-HIFI – 1-760-710-0992
7
1 9 6 9 K e l l o g g A v e n u e , C a r l s b a d , C A 9 2 0 0 8
1 - 7 6 0 - 7 1 0 - 0 9 9 2
1 - 8 0 0 - B U Y - H I F I
–
w w w . n i l e s a u d i o . c o m
©2011 The AVC Group, llC. All rights reserved. Niles and the Niles logos are registered
trademarks of The AVC Group, llC. All other trademarks are the property of their respective
owners. We reserve the right to change specifications, descriptions and prices without notice.
The technical and other information contained herein is not intended to set forth all technical
and other specifications. designed and engineered in the uSA. 9901211 Rev A
|