User’s Guide for
Nokia Image Frame SU-7
9311006
Issue 1
Contents
FOR YOUR SAFETY ................... 4 3. Using the Nokia
Image Frame........................... 16
Introduction ............................. 6
Power supply................................... 6
Technical data................................. 6
Image format.................................. 7
Viewing the images .................... 16
Editing the images...................... 16
Switching the screensaver
on and off...................................... 17
Modifying the display
1. Overview............................... 8
brightness...................................... 18
Sending an image from the
2. Getting started .................. 11
Setting up the Nokia Image
Nokia Image Frame..................... 18
Receiving images with the
Frame............................................... 11
Switching the power on
Nokia Image Frame..................... 18
Receiving images over MMS
with the Nokia Image Frame.... 20
and off ............................................ 12
Keying in the PIN code............... 13
Configuring the MMS
settings........................................... 13
OTA message ..................................... 14
SMS messages................................... 14
Care and maintenance ...........22
Important Safety Information 23
3
F O R Y O U R S A F E T Y
FOR YOUR SAFETY
Read these simple guidelines. Breaking the rules may be dangerous or illegal.
Further detailed information is given in this manual.
Do not connect the Nokia Image Frame to the mobile network when
wireless phone use is prohibited or when it may cause interference or
danger.
INTERFERENCE
All devices may get interference, which could affect performance.
SWITCH OFF IN HOSPITALS
Follow any regulations or rules. Do not connect the Nokia Image
Frame to the mobile network near medical equipment.
SWITCH OFF WHEN REFUELLING
Do not connect the Nokia Image Frame to the mobile network at a
refuelling point. Don't use near fuel or chemicals.
SWITCH OFF NEAR BLASTING
Do not connect the Nokia Image Frame to the mobile network where
blasting is in progress. Observe restrictions, and follow any
regulations or rules.
USE SENSIBLY
Use only in the normal position. Don't touch the antenna
unnecessarily.
QUALIFIED SERVICE
Only qualified personnel may install or repair the Nokia Image Frame
equipment.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its user's guide for
detailed safety instructions. Do not connect incompatible products.
BACKUP COPIES
Remember to make backup copies of all important data.
WATER-RESISTANCE
Your Nokia Image Frame is not water-resistant. Keep it dry.
4
F O R Y O U R S A F E T Y
IMPORTANT:
Only use chargers in dry conditions. Never supply power to the device
with a charger when the device or charger or their parts are damp or
wet. If the device has been exposed to salt water, wipe it immediately
with a cloth dampened with fresh water to avoid corrosion. The device
must then be carefully wiped dry.
Do not point the IR (infrared) beam at anyone's eye or allow it to
interfere with other IR devices. This device is a Class 1 Laser product.
I Network Services
The Nokia Image Frame described in this guide is approved for use on the EGSM
900 and GSM1800 network.
A number of features included in this guide are called Network Services. These
are special services that you arrange through your wireless service provider.
Before you can take advantage of any of these Network Services, you must
subscribe to them through your service provider and obtain instructions for their
use from your service provider.
Note: Some networks may not support all language-dependent
characters and/or services.
5
I n t r o d u c t i o n
Introduction
The Nokia Image Frame SU-7 is an enhancement product, which enables
you to view the digital images taken or received by your IrDA-enabled
Nokia phone or other compatible devices. You can connect the Nokia
Image Frame to the devices using its infrared (IR) port. If you insert a
SIM card to the Nokia Image Frame, you can also receive new images as
MMS messages.
You can place the Nokia Image Frame on a table and view the images
either one-by-one or as a slide show. The Nokia Image Frame comes
supplied with three pre-loaded images, and you can conveniently add
new images from a compatible device and delete old images.
Read this user’s guide carefully before using the Nokia Image Frame.
I Power supply
Check the model number of any charger used to supply power before use
with this device. The Nokia Image Frame is intended for use with the
ACW-5A charger.
Warning! Use only chargers approved by the manufacturer for
use with this particular enhancement. The use of any other
types will invalidate any approval or warranty applying to the
enhancement, and may be dangerous.
For availability of approved chargers, please check with your dealer.
When you disconnect the power cord of any enhancement, grasp and
pull the plug, not the cord.
I Technical data
• Weight: 570 g
• Width (max) / height (max) / depth (max):
170 mm / 129 mm / 123.0 mm
• Display: 5.1" transmissive backlit STN color LCD 320 x 240 horizontal
orientation, 4096 colors. The image resolution in these materials
may appear different.
6
I n t r o d u c t i o n
• Operating temperature: 0 oC to 40 oC
• Compatibility: The Nokia Image Frame SU-7 is compatible with
phones and other devices that support image sending over infrared
(IrDA). Note that if image sending cannot be activated from the
phone (IrDA Send feature), the Nokia Image Frame can pull the
images from the compatible Nokia phone when the phone’s IR
connection has been activated. The Nokia Image Frame can also
receive images over MMS from most MMS-enabled phones.
• IrDA standards: IrOBEX 1.3 receive/send, IrTranP receive
• Supported image format: JPEG and GIF (not animated GIF)
• Supported image size: max 1024 x 768, up to 200 kB. Due to
different techniques of image processing, even up to 1 MB.
I Image format
The Nokia Image Frame converts all the received images to JPEG format
with the 320 x 240 pixel resolution. If the resolution of the received
image differs from this resolution, the Nokia Image Frame scales the
image so that it fits optimally on the display.
When you send images from the Nokia Image Frame, they are sent with
the JPEG format, since the Nokia Image Frame does not store the
original formats of the received images. You should therefore remember
to make backup copies of your original images.
7
O v e r v i e w
1. Overview
The Nokia Image Frame has the following parts:
1. Display
2. Infrared (IR) port
3. Control keys
4. Table support
5. Charger connector
6. Back cover
You can use the Nokia Image Frame through the control keys on top of
the device. The control keys are:
1. Power on/off key
2. Show/Brightness key
3. Rotation key
8
O v e r v i e w
4. Three-position switch:
• Slide show mode
• Image view mode
• Edit mode
5. Up key
6. Down key
7. Mark key
8. IrDA key
There are three ways to press the keys. These are as follows:
• Press briefly - press a key for less than one second
• Press - press a key for at least one second
• Press and hold - press and hold down the key for at least three
seconds
Indicators on the display
This indicator shows that the image has been marked for
viewing.
The memory in the Nokia Image Frame is full, 50 images are
stored in the Nokia Image Frame. If the memory becomes full
in the middle of image transfer, the rest of the images are
discarded.
The Nokia Image Frame is rotating the image 90o clockwise.
The Nokia Image Frame is switching to the next image.
The Nokia Image Frame is switching to the previous image.
Confirms that the image has been successfully deleted.
9
O v e r v i e w
This indicator blinks when the Nokia Image Frame attempts to
establish the IrDA connection. When the connection is
established and the Nokia Image Frame is sending or receiving
an image, the indicator is displayed continuously.
Confirms that the images have been successfully received or
sent (the receiving device has confirmed the images as
received).
The image is not supported by the Nokia Image Frame. It is, for
example, too large or not in the compatible format.
An error occurred during the image transfer.
This indicator blinks when the Nokia Image Frame is
downloading an incoming MMS message. When the message
has been stored to the Nokia Image Frame, the indicator is
displayed continuously until you check the message and either
accept it or delete it.
The network connection has been established. When the
connection has not been established, there is a / mark across
the icon.
GPRS service is available. When the service is not available,
there is a / mark across the icon.
This indicator shows how many images have been
marked for viewing and how many images in total have
been stored. The maximum number of stored images is
50.
The progress bar is shown while the Nokia Image Frame
processes the received images.
10
G e t t i n g s t a r t e d
2. Getting started
I Setting up the Nokia Image Frame
Warning! To avoid damage to the SIM card, do not install, move
or remove the SIM card if the power supply is connected to an
AC wall outlet.
1. If you want to be able to receive images over MMS, you have to
insert a SIM card into the Nokia Image Frame.
1. With the display of the Nokia Image Frame facing you, detach the
cover on the back of the Nokia Image Frame by pushing it down
forward.
2. Insert the SIM card to the SIM card holder so that the contact
surface of the SIM card is up and the bevelled corner of the card is
on the right and facing away from you.
3. Put the cover back on the Nokia Image Frame.
11
G e t t i n g s t a r t e d
2. Connect the lead from
the charger to the
socket at the back of
the Nokia Image Frame
(1).
3. Connect the charger to
an AC wall socket.
4. Set the Nokia Image
Frame on the table
with the control keys
on the top. If most of
your images are in the
upright position, you can turn the Nokia Image Frame upright so that
the control keys are on the right side of the display.
Note: All radio transmitting devices send signals that may
cause interference in different electronic devices (PC,
television, etc.). To avoid interference, place the Image
Frame far enough from other electronic devices.
You can turn the table support at the back to change the position
angle of the Nokia Image Frame (2).
I Switching the power on and off
Press to switch on the Nokia Image Frame.
Note that if the SIM card is inserted and you switch the Image Frame on,
the Image Frame automatically connects to the mobile network. Do not
switch the Image Frame on when the SIM card is inserted, if the use of
mobile devices (such as mobile phones) is prohibited.
Press to switch off the power.
Note that if the SIM card is full, it can take up to a minute before the
Nokia Image Frame turns on and shows the first image.
Unplug the Nokia Image Frame when not in use.
12
G e t t i n g s t a r t e d
I Keying in the PIN code
If the PIN query is activated on the SIM card, the Nokia Image Frame
displays the PIN query when the power is switched on.
Note: If you want to deactivate the PIN query, insert the SIM
card to your phone and deactivate the PIN query as instructed
in your phone’s user guide.
1. Press briefly
is highlighted.
or
until the correct first number of the PIN code
2. Press briefly
to select the number.
The * character appears on the display to indicate that the first
number has been selected.
3. Select the rest of the numbers as in steps 1 and 2.
4. If the PIN code is correct, the Nokia Image Frame displays the
icon. If the PIN code is incorrect, the
have to key in the PIN code again.
icon is displayed, and you
I Configuring the MMS settings
If the MMS settings are preloaded to the Nokia Image Frame, you can
skip this section unless you want to reconfigure the MMS settings.
Check with your dealer if the MMS settings have been preloaded. If the
settings are not preloaded and you want to receive images over MMS,
you can configure the MMS settings by an over-the-air (OTA) message
or SMS messages, as explained further below.
Note that many operators also offer a web-based OTA service for MMS
settings. Check with your operator if this service is available.
If the configuration succeeds, the Nokia Image Frame displays the
icon. If the configuration fails, the
icon is displayed, and you have to
send the configuration messages again.
13
G e t t i n g s t a r t e d
OTA message
You can configure the MMS settings by an OTA message if your operator
offers that service.
Note: Before receiving the settings, set the Nokia Image Frame
to the edit mode by sliding the three-position switch to
.
Send a text message 91 <service_number> <operator_specific_text>
from your mobile phone to the phone number of the SIM card you
inserted to the Nokia Image Frame. For example, 91 12345 mms. For
the exact content of the message, contact your operator.
The Nokia Image Frame uses that message to send another message to
the operator’s OTA service. When the Nokia Image Frame receives a reply
containing the settings, it stores them automatically.
SMS messages
If your operator does not offer the OTA service, you can send the settings
to the Nokia Image Frame yourself using SMS messages.
Note: Before sending the settings, set the Nokia Image Frame to
the edit mode by sliding the three-position switch to
.
You have to send the SMS commands listed below to the phone number
of the SIM card you inserted to the Nokia Image Frame. For the exact
values needed in the commands, contact your service provider.
• 31 <access_point_name>
Command for setting the GPRS access point name.
• 32 <URL_address>
Command for setting the MMS Center address.
• 41 <username>
Command for setting the user name for the MMS connection.
• 42 <password>
Command for setting the password for the MMS connection.
• 33 <IP_address>
Command for setting the gateway IP address.
14
G e t t i n g s t a r t e d
• 27 <number>
Command for setting the SMS Center number.
• 43 <on_or_off>
Command for setting the password prompting on or off.
• 45 <on_or_off>
Command for setting the connection security on or off.
• 44 <1_or_2>
Command for setting the authentication method for the connection.
The method is normal (1) or secure (2).
• 46 <1_or_2>
Command for setting the session mode. The mode is temporary (1) or
permanent (2).
• 22 <on_or_off>
Command for activating or disactivating the PIN query.
• 99
Command for restoring the factory settings. The Nokia Image Frame
has no MMS settings by default.
• 9
Command for checking the current settings. The Nokia Image Frame
sends back the settings to the number from where the command was
sent.
You can either send the commands one by one, or combine several
commands in one message. If you combine the commands, you have to
separate each command with a comma (no spaces). For example, 31
APN1,43 on,44 1.
If you send any erroneous commands, you can send them again with the
correct values. If the settings are correct but the Nokia Image Frame is
not receiving images over MMS, contact your operator for
troubleshooting.
15
U s i n g t h e N o k i a I m a g e F r a m e
3. Using the Nokia Image Frame
I Viewing the images
If there is only one image in the Nokia Image Frame, it is displayed when
you switch on the power. If there is more than one image in the Nokia
Image Frame, you can set the Nokia Image Frame to show just one
image, or several images in rotation as a slide show.
Setting Nokia Image Frame to show one image:
1. Slide the three position switch to
.
2. Press briefly or to scroll through the images and select the
image you want to view. If you press and hold
scroll automatically at 3-second intervals.
or , the images
You can scroll through all the marked images. For more information
about marking the images, see ”Editing the images” on page 16.
Setting Nokia Image Frame to show the slide show:
• Slide the three position switch to
.
The Nokia Image Frame displays all the marked images in rotation so
that each image is shown for 30 seconds at a time. For more
information about marking the images, see ”Editing the images” on
page 16.
I Editing the images
When the power is switched on and the edit mode activated, you can
delete the images and mark the images you want for viewing.
Deleting images:
Remember to make backup copies of your images by, for example,
sending and saving them to another compatible device.
1. Slide the three position switch to
2. Press briefly or until the Nokia Image Frame displays the
image you want to delete.
.
3. Press and hold
and
until the
icon is displayed.
16
U s i n g t h e N o k i a I m a g e F r a m e
Marking the images for viewing:
1. Slide the three position switch to
2. Press briefly or to scroll the images.
.
3. If you want to be able to view an image, mark it by pressing briefly
while the image is displayed. The Nokia Image Frame displays
the
press briefly
icon for all marked images. If you want to unmark an image,
while the marked image is displayed.
When the Nokia Image Frame receives new images, it automatically
marks them. If you do not want to view the new images, unmark
them as explained above.
Rotating images:
You can rotate the images both in the edit mode and when you are
viewing the images.
When the image you want to rotate is displayed, press
to rotate the
image 90o clockwise. The Nokia Image Frame stores the orientation of
the image, and the next time the Nokia Image Frame displays the image,
it uses the new orientation.
I Switching the screensaver on and off
You can activate the screensaver, if you want to turn off the display
without turning off the device. Press and hold
screensaver. If there are unchecked MMS images in the Nokia Image
Frame, the icon continues to be displayed even when the
screensaver is activated. If a new MMS image is downloaded while the
screensaver is on, the icon appears on the screen.
to activate the
You can turn the display back on by pressing any control key.
The Nokia Image Frame activates the screensaver automatically if no
keys have been pressed for 18 hours.
17
U s i n g t h e N o k i a I m a g e F r a m e
I Modifying the display brightness
When the power is switched on, you can modify the brightness of the
display by pressing briefly . There are five brightness levels, and each
time you press , the level is raised by one. When the highest
brightness level is used and you press , the Nokia Image Frame
returns to the lowest brightness level.
I Sending an image from the Nokia Image Frame
When the power is switched on, select the image you want to send on
the display of the Nokia Image Frame.
1. If needed, activate the IR port of the device to which you want to
send an image.
2. Direct the IR ports of the Nokia Image Frame and the receiving
compatible device toward each other, and ensure that there are no
obstructions between the devices. The maximum allowed distance is
up to 1.5 m and the transmission angle 15o.
3. Press
Nokia Image Frame attempts to establish a connection to the
receiving device. During the image transfer the icon stops
blinking. When the image is successfully sent, the Nokia Image
Frame displays the icon.
and
to send the image. The
icon blinks while the
I Receiving images with the Nokia Image Frame
When the power is switched on, the Nokia Image Frame can receive
images. Note that the Nokia Image Frame converts the received images
to display them. For more information, see ”Image format” on page 7.
The image receiving procedure differs depending on the sending device.
If the sending device can send images over IR, you can send the selected
images from the device while the Nokia Image Frame is in the passive IR
reception mode. If image sending cannot be activated from the sending
device, the Nokia Image Frame can pull all the images from the sending
device’s default image folder using the active IR reception mode.
18
U s i n g t h e N o k i a I m a g e F r a m e
Receiving images over IR:
1. If you want the images in the Nokia Image Frame to be in a certain
order, press briefly or to scroll to the image after which you
want to store the new images.
2. Direct the IR ports of the Nokia Image Frame and the compatible
sending device toward each other, and ensure that there are no
obstructions between the devices. The maximum allowed distance is
up to 1.5 m and the transmission angle 15o.
3. When the sending device starts to send the images, the Nokia Image
Frame enters the passive IR reception mode and displays the
icon. For more information on how to initiate sending from the other
device, refer to the user’s guide of that device.
4. During the image transfer, the Nokia Image Frame displays the
icon and the received images one by one.
5. After the images have been received, the Nokia Image Frame returns
to the previous mode, and the images are stored as the next images
after the currently displayed image.
If you want to edit the new images, see ”Editing the images” on page
16.
Pulling images over IR:
The Nokia Image Frame pulls all the images from the image source
device’s default directory. The maximum number of images in the Nokia
Image Frame is 50. If this limit is reached during the image transfer, the
transfer is disconnected so that only 50 images in total are stored to the
Nokia Image Frame.
1. If you want the images in the Nokia Image Frame to be in a certain
order, press briefly
or
to scroll to the image after which you
want to store the new images.
2. Direct the IR ports of the Nokia Image Frame and the compatible
image source device toward each other, and ensure that there are no
obstructions between the devices. The maximum allowed distance is
up to 1.5 m and the transmission angle 15o.
19
U s i n g t h e N o k i a I m a g e F r a m e
3. Activate the image source device’s IR connection. For more
information on how to do this, refer to the user’s guide of that
device.
4. Press
to enter the active IR reception mode. The Nokia Image
icon.
Frame displays the
5. During the image transfer, the Nokia Image Frame displays the
icon and the received images one by one.
6. After all the images have been received, the Nokia Image Frame
returns to the previous mode, and the images are stored as the next
images after the currently displayed image.
If you want to edit the new images, see ”Editing the images” on page
16.
I Receiving images over MMS with the Nokia
Image Frame
Note: Your Nokia Image Frame must be connected to the
mobile network to use this function. Do not connect the Nokia
Image Frame to the mobile network when wireless phone use is
prohibited or when it may cause interference or danger.
When the power is switched on and the Nokia Image Frame is connected
to the mobile network, it can receive images over MMS. Note that the
Nokia Image Frame converts the received images to display them. For
more information, see ”Image format” on page 7. If the incoming MMS
message contains sound or text, only the image is stored.
The incoming image makes the Nokia Image Frame enter the MMS
reception mode and display the
downloaded, the icon blinks and the image on the display does not
change even if the Nokia Image Frame is in the slide show mode. When
the download is finished, the icon stops blinking. If you turn the
icon. While the image is
power off from the Nokia Image Frame during the image download, all
the incompletely downloaded images are discarded.
The downloaded image is not displayed before you check the image. The
icon is displayed until you have checked and accepted or deleted
the image. If more than one image has been downloaded, the number of
downloaded images is shown next to the icon.
20
U s i n g t h e N o k i a I m a g e F r a m e
Checking the images:
1. If you want the images in the Nokia Image Frame to be in a certain
order, press briefly or to scroll to the image after which you
want to store the new images.
2. Press briefly to view the oldest unchecked image in the memory.
If the phone number of the sender is known, it is displayed on the
screen with the downloaded image.
3. If you want to store the image, press briefly . The image is stored
as the next image after the previously displayed image. The phone
number is not stored.
If you want to delete the image immediately, press and hold
until the icon is displayed.
and
21
C a r e a n d m a i n t e n a n c e
Care and maintenance
Your Nokia Image Frame SU-7 is a product of superior design and craftsmanship
and should be treated with care. The suggestions below will help you to fulfil any
warranty obligations and to enjoy this product for many years.
•
•
Keep all enhancements out of the reach of small children.
Keep Nokia Image Frame dry. Precipitation, humidity and all types of liquids
or moisture can contain minerals that will corrode electronic circuits.
•
•
Do not use or store Nokia Image Frame in dusty, dirty areas. Its moving parts
can be damaged.
Do not store Nokia Image Frame in hot areas. High temperatures can shorten
the life of electronic devices, damage batteries, and warp or melt certain
plastics.
•
Do not store Nokia Image Frame in cold areas. When it warms up (to its
normal temperature), moisture can form inside, which may damage
electronic circuit boards.
•
•
•
•
Do not attempt to open Nokia Image Frame. Non-expert handling may
damage it.
Do not drop, knock or shake Nokia Image Frame. Rough handling can break
internal circuit boards.
Do not use harsh chemicals, cleaning solvents, or strong detergents to clean
Nokia Image Frame.
Do not paint Nokia Image Frame. Paint can clog the moving parts and prevent
proper operation.
If Nokia Image Frame is not working properly, take it to your nearest qualified
service facility. The personnel there will assist you and, if necessary, arrange for
service.
For environmentally sound recycling, contact your local Nokia service point or
check local regulations for correct disposal of household electronics.
22
I m p o r t a n t S a f e t y I n f o r m a t i o n
Important Safety Information
I Power supply
The Image Frame power supply ACW-5A converts mains voltage to low voltage
DC.
Note: The power supply socket should be easily accessible, and it must not be
covered. The power supply is insulation class 2-covered.
Warning: Dangerous voltage. Do not attempt to open the casing under the back
cover.
Note: This power supply is for indoor use only! Do not expose the unit to water,
rain or dust.
The power supply should be disconnected from the socket when the device is not
in use for a prolonged period of time or when the power supply is not connected
to the device.
I Operating environment
Remember to follow any special regulations in force in any area and always
disconnect the Nokia Image Frame from the mobile network whenever it is
forbidden to use it, or when it may cause interference or danger.
Use the Nokia Image Frame only in its normal operating positions.
Do not place credit cards or other magnetic storage media near the Nokia Image
Frame, because information stored on them may be erased.
I Electronic devices
Most modern electronic equipment is shielded from radio frequency (RF) signals.
However, certain electronic equipment may not be shielded against the RF
signals from your Nokia Image Frame.
Pacemaker manufacturers recommend that a minimum separation of 20 cm (6
inches) be maintained between a handheld wireless phone and a pacemaker to
avoid potential interference with the pacemaker. These recommendations are
consistent with the independent research by and recommendations of Wireless
Technology Research. Persons with pacemakers:
•
Should always keep the Nokia Image Frame more than 20 cm (6 inches) from
their pacemaker when the Nokia Image Frame is connected to the mobile
network;
•
If you have any reason to suspect that interference is taking place, switch off
your Nokia Image Frame immediately.
23
I m p o r t a n t S a f e t y I n f o r m a t i o n
Hearing aids
Some digital wireless phones may interfere with some hearing aids. In the event
of such interference, you may want to consult your service provider.
Other medical devices
Operation of any radio transmitting equipment, including the Nokia Image
Frame, may interfere with the functionality of inadequately protected medical
devices. Consult a physician or the manufacturer of the medical device to
determine if they are adequately shielded from external RF energy or if you have
any questions. Disconnect the Nokia Image Frame from the mobile network in
health care facilities when any regulations posted in these areas instruct you to
do so. Hospitals or health care facilities may be using equipment that could be
sensitive to external RF energy.
Posted facilities
Disconnect the Nokia Image Frame from the mobile network in any facility where
posted notices so require.
I Potentially explosive atmospheres
Disconnect the Nokia Image Frame from the mobile network when in any area
with a potentially explosive atmosphere and obey all signs and instructions.
Sparks in such areas could cause an explosion or fire resulting in bodily injury or
even death.
Users are advised to disconnect the Nokia Image Frame from the mobile network
when at a refuelling point (service station). Users are reminded of the need to
observe restrictions on the use of radio equipment in fuel depots (fuel storage
and distribution areas), chemical plants or where blasting operations are in
progress.
Areas with a potentially explosive atmosphere are often but not always clearly
marked. They include below deck on boats; chemical transfer or storage facilities;
vehicles using liquified petroleum gas (such as propane or butane); areas where
the air contains chemicals or particles, such as grain, dust or metal powders; and
any other area where you would normally be advised to turn off your vehicle
engine.
24
|