Enterprise Edge
Telephone Feature
Card
© 1999 Nortel Networks
P0908931 Issue 01
Using Enterprise Edge features
1. Press ƒ and enter the desired feature code on the dial pad.
Using an
Enterprise
Edge
or
Press a programmed memory button.
2. Follow the display messages.
On a two-line display telephone, some features are also available on display
feature
buttons.
You can program memory buttons for one-touch access to frequently used
features.
Programming
memory
buttons
1. Press ƒ•‹.
2. Press the memory button that you want to program. (This step is not necessary
on the M7100 telephone.)
3. Press ƒ and enter the feature code on the dial pad.
You can also program frequently dialed numbers, using the following codes:
ƒ•⁄ External autodial: Store an external number for one-touch
dialing.
ƒ•¤ Internal autodial: Store an internal number for one-touch
dialing.
See your Telephone User Card for details.
You cannot program line, intercom, answer, or Handsfree/Mute buttons.
Enterprise Edge features
ƒ°fl
Cancel ƒ£°fl
Background
Music
Listen to music (provided by your office) through your telephone speaker when
you are not on a call.
Button
Inquiry
ƒ•‚
Check what is programmed on any button. Use when labeling buttons.
Call Duration ƒ‡‡
Briefly display the approximate length of your current or most recent call.
Timer
Call Forward ƒ›
Cancel ƒ£›
Send your calls to another telephone in your Enterprise Edge system.
ƒ‡›
Call Park
Put a call on hold so that it can be picked up from any telephone in your
Enterprise Edge system. The display shows a three-digit retrieval code.
To retrieve a parked call, press ∆ and dial a retrieval code on any
telephone in your Enterprise Edge system. On the M7100 telephone, just lift the
receiver and dial the retrieval code.
ƒ‡fl
Answer any ringing telephone.
Press ƒ‡fl and dial that telephone’s extension number.
Call Pickup -
directed
ƒ‡fi
Answer a call that is ringing at another telephone in your pickup group. The
external call that has been ringing longest is answered first.
Call Pickup -
group
Page 1 - Enterprise Edge Telephone Feature Card
ƒ°‚⁄
Answer the next call. If more than one call is waiting, priority is given to incoming
external calls over callback, camped, or transferred calls.
Call Queuing
Camp-on
ƒ°¤
Re-route a call to another telephone even if all its lines are busy.
Press ƒ°¤, then dial the extension number of the receiving
telephone.
Class of
service
password
ƒfl°
Change the dialing filters on a line or telephone, or gain external access to your
system. Dialing filters determine which numbers you can dial.
Press ƒfl° and enter a password provided by your system
coordinator to change your class of service.
Conference
ƒ‹
Establish a conference call between yourself and two other parties.
1. Make or answer the first call.
2. Put the first call on hold.
3. Make or answer the second call.
4. After the second call is connected, press ƒ‹.
5. Press the line or intercom button of the first held call (not required on the M7100
telephone).
6. Press ® to end the conference call.
To remove yourself from a conference permanently (unsupervised conference):
Press ƒ‡‚. The other two callers remain connected. (Some
external lines may not support this feature. See your system coordinator.)
To put a conference on hold:
Press ˙. The other two callers can still talk to each other.
To split a conference:
Press the line or intercom button of one caller to consult privately while the other
caller is on hold. To re-establish the conference, press ƒ‹.
To disconnect one party:
Press the line or intercom button of the caller you want to disconnect, then press
®. Press the line or intercom button of the remaining caller to resume your
conversation.
To independently hold two calls:
Press the line or intercom button of the first caller, then press ˙. The
second caller is automatically put on hold. To re-establish the conference, retrieve
one call from hold, press ƒ‹, then retrieve the second call from hold.
ƒ•‡
Contrast
Adjust the contrast of your display.
adjustment
Press ƒ•‡, then press a number from ⁄ to · (depending on
your telephone). Press ˙ to set your choice.
ƒ•°¤
Dialing modes
Choose one of three methods of dialing.
1. Press ƒ•°¤.
2. Press £ to select the mode.
3. Press ˙to store the mode.
Standard Dial: Select a line, then dial the number. (Standard Dial is always
available, even when another dialing mode is selected.)
Page 2 - Enterprise Edge Telephone Feature Card
Automatic Dial: Dial the number without choosing a line button first. Your prime
line is automatically selected for the call.
Pre-Dial: Dial the number, then press a line button to place the call. Edit the
number by pressing √ before placing the call.
ƒ°fi
Cancel ƒ£°fi
Do Not
Disturb
When you are not on a call prevent all incoming calls, except priority calls, from
ringing at your telephone. When you are on a call, block an incoming priority call.
Group
Listening
ƒ°‚¤
Cancel ƒ£°‚¤
Use both the receiver and speaker while you are on a call. To avoid electronic
feedback, keep the receiver away from the speaker during the call, and press
® to hang up.
˙
Hold
Temporarily suspend a call.
To retrieve a held call, press the line button for the held call.
(Press ˙ on the M7100 telephone.)
Exclusive Hold
ƒ‡· or ƒ˙
Temporarily suspend a call and prevent other telephones from picking it up.
Language
Choice
ƒ•fi‚⁄
Select English as the language for the telephone display.
ƒ•fi‚¤
Select French as the language for the telephone display.
ƒ•fi‚‹
Select Spanish as the language for the telephone display.
Last
ƒfi
Automatically redial the last external telephone number that you dialed.
Number
Redial
Line pools
ƒfl›
With a line pool, telephones can share several lines for making calls.
1. Press ƒfl› or ∆.
2. Enter a line pool access code. (See your system coordinator for a list.)
Line
ƒ°›
Cancel ƒ£°›
Send calls arriving on an external line to another telephone outside your
Enterprise Edge system. (Some external lines may not support this feature. See
your system coordinator.) This feature is not available on the M7100 telephone.
Redirection
Link
ƒ‡⁄
Generate a Link signal ‹ to access a PBX or other host exchange.
ƒ°‚°
Long Tones
Generate a tone for as long as you hold down a button. This is used to
communicate with devices like fax or answering machines. Long tones are in
effect only for your current call.
Page 3 - Enterprise Edge Telephone Feature Card
ƒ⁄
Cancel ƒ£⁄
Messages
Send a message to an Enterprise Edge telephone’s display to have someone call
you back.
To view and reply to your messages:
1. Press ƒflfi.
2. Press • and £ to view your message list.
3. Press ‚ to call the person who left you the message.
To erase a message:
1. Press ˙ while viewing a message.
ƒ•°⁄
Change the position of your line or hunt group buttons.
1. Press ƒ•°⁄.
Moving line
buttons
2. Press the line button that you want to move.
3. Press the button that you want to move the line to.
4. Press ®. The two buttons are exchanged.
5. Switch the button caps.
Line buttons cannot be exchanged with intercom, answer or Handsfree/Mute
buttons.
ƒ•°⁄·
Block the outgoing name and/or number on a per-call basis.
1. Press ƒ•°⁄·.
Name and
number
blocking
ƒfl‚ and code (1 to 3) and zone (0 to 6)
Make a page announcement through either the internal (code 1) or external (code
2) speakers, or both (code 3). Zone 0 pages all zones.
Page announcements are programmed to timeout after a pre-selected amount of
time which is set by your installer.
Page
Internal page
ƒfl⁄ and zone (0 to 6)
Make a page announcement to all, or to a specific group of Enterprise Edge
telephones, through the telephone speakers. Zone 0 pages all zones.
External page
ƒfl¤
Make a page announcement through an external loudspeaker system.
Internal and external page
ƒfl‹ and zone (0 to 6)
Make a page announcement through both your Enterprise Edge telephone
speakers and an external loudspeaker system. Zone 0 pages all zones.
ƒ‡°
Pause
Program in an external autodial sequence to insert a 1.5 second delay ›.
For pulse dialing: • also inserts a 1.5 second delay.
Priority
ƒfl·
Interrupt a person who is on a call or using Do Not Disturb.
A person on another call can press ƒ°fito block your priority call.
Page 4 - Enterprise Edge Telephone Feature Card
ƒ°‹
Privacy
Change the privacy setting for an external line. If a line normally has privacy, this
permits another telephone that shares the line to join your call by selecting the
line while you are using it. If a line normally has privacy disabled, this prevents
another telephone that shares the line from joining your call by selecting the line
while you are using it. The privacy setting is re-established once you end your call
or when you enter the Privacy feature code again.
Programmed
Release
ƒ•°·
Program at the end of an external autodial number to automatically release fi the
call.
Ring Again
ƒ¤
Cancel ƒ£¤
Monitor a busy or unanswered telephone, or a busy line pool within your system.
Ring Again signals you to call back when the telephone or line pool becomes
available.
ĥfl
Ring type
Select a distinctive ring to help differentiate between your telephone and others
nearby.
1. Press ĥfl.
2. Enter the ring type number (⁄ to ›).
3. Press ˙.
ƒ•°‚
Ring
Make your telephone ring so that you can adjust the volume. You can also adjust
the volume any time your telephone rings.
volume
ƒ•·
Run/Stop
Store more than one autodial number or external carrier feature code on one
memory button by inserting a break point fl between numbers or codes. The first
press of the button dials the first number or code; the next press dials the next
number or code. You can program up to four numbers or codes separated by
break points.
ƒfl‡
Saved
Save a number to redial later. Enter the code while you are on a call that you have
dialed to save the number. Enter the code when you are not on a call to redial the
saved number.
Number
Redial
Show service schedules
Service
ƒ°‡‚
Schedules
Display the modes that have been turned on at a designated control set.
Ringing service
ƒ°‡⁄
Cancel ƒ£°‡⁄
Turn on one of six schedules for alternative ringing/call answering arrangements
from a designated control telephone.
Restriction services
ƒ°‡¤
Cancel ƒ£°‡¤
Turn on one of six services for restrictions on particular lines or telephones from a
designated control telephone. You will be required to enter the System
Coordinator password.
Routing services
Page 5 - Enterprise Edge Telephone Feature Card
ƒ°‡‹
Cancel ƒ£°‡‹
Turn on one of six services for routing on particular lines or telephones from a
designated control telephone. You will be required to enter the System
Coordinator password.
Speed Dial
ƒ‚
Dial an external telephone number using a two-digit code. There are two types of
speed dial codes: system (01 to 70) and personal (71 to 94). System speed dial
codes can be used from any Enterprise Edge telephone in the system. They are
assigned by your system coordinator. Personal speed dial codes are used
exclusively at your telephone. To make a call using a speed dial code:
1. Press ƒ‚.
2. Enter the two-digit code for the number (01 to 70 for system speed dial, 71 to
94 for personal speed dial).
To program personal speed dial numbers:
1. Press ƒ•›.
2. Enter a two-digit code from 71 to 94.
3. Specify the external line by pressing a line button, a line pool button, or the
intercom button. If you don’t specify the external line, the system automatically
chooses a line for the call.
4. Dial the telephone number you want to program (up to 24 digits).
5. Press ˙.
6. Record the code and number you have just programmed.
You cannot program personal speed dial numbers while someone else is
programming your Enterprise Edge system.
Static time
and date
ƒ°‚fl
Change the first line of the display to the current time and date.
Cancel ƒ£°‚fl
Time
ƒ°‚‹
Briefly display the time and date while you are on a call.
Transfer
ƒ‡‚
Send a call to another telephone within your Enterprise Edge system, or to an
external telephone. You may not be able to transfer a call on an external line to an
external telephone, depending on the capabilities of the lines.
1. Make or answer a call.
2. Press ƒ‡‚.
3. Call the person you want to transfer the call to.
4. Stay on the line if you wish to speak to the person first.
5. Press ® to complete the transfer.
If an external call is transferred to a busy internal or network extension, or is not
answered after a few rings, the call automatically rings you back.
Trunk
ƒ°‚‚
Answer an external call that is ringing on a line that has been placed into a
Ringing Service schedule from any telephone in your Enterprise Edge system.
This feature does not work for a private line.
Answer
Voice call
ƒflfl
Make a voice announcement or begin a conversation through the speaker of
another Enterprise Edge telephone without first making the other telephone ring.
Page 6 - Enterprise Edge Telephone Feature Card
ƒ°°
Cancel ƒ£°°
Voice call
deny
Prevent your telephone from receiving voice calls.
Do Not Disturb (ƒ°fi) also prevents your telephone from receiving
voice calls.
Wait for dial
tone
ƒ°‚›
Program in an external autodial number to cause the system to wait to receive dial
tone ‡ from another system before proceeding with the dialing sequence.
Call Display Services
The following features are available only if you subscribe to Call Display services
from your local telephone company.
Autobumping
ƒ°⁄fi
Cancel ƒ£°⁄fi
Have the system automatically delete the oldest log item from a full Call Log, so
that a new log item can be stored.
Call
Information
ƒ°⁄⁄
Display the name, number or line name of a ringing or held call. Press £ to
move through the information displays.
Call Log
ƒ°⁄¤
Call Log displays use the following special characters:
1
¯
(underline) identifies a new item
identifies answered calls
§
/
identifies long distance calls
identifies that the information has been shortened
To view your Call Log:
1. Press • to view old items.
Press £ to view new items.
Press ‚ to return to the last viewed item.
2. Press £ and • to move through your items.
3. Press √ to view more information on an item.
To erase a Call Log entry:
1. Press ˙ while viewing an item.
To return a call from your Call Log:
1. Display the desired number on your telephone.
2. Edit the number, if required. You can add numbers for long distance dialing or
line pool access or remove numbers using √.
3. Press a line button.
4. Lift the receiver.
Call Log
options
ƒ•°›
Select the type of calls that will automatically be stored in your Call Log. Press£
to see the next setting. Press ˙ to select the displayed setting.
Call Log
password
ƒ•°fi
Program a four-digit password for your Call Log. To remove a forgotten password,
see your system coordinator.
ƒ°⁄‹
Logit
Store caller information for your current call in your Call Log.
P0908931 Issue 01
Page 7 - Enterprise Edge Telephone Feature Card
|