Cat. No. 31-3032
Digital Synthesize
Audio/Video
Surround Receive
R
STAV-3370
Owner’s Manual
Please read before using this equipment.
IMPORTANT SAFETY INSTRUCTIONS
This receiver is made and tested to meet exacting
safety standards. It meets both UL and FCC require-
ments
Careful attention is devoted to quality standards in the manufacture of your receiver, and safety is
a major factor in its design. However, safety is also your responsibility.
This section lists important information that will help you properly use and enjoy your receiver and
accessories. Read all the included safety and operating instructions before using your receiver. Fol-
low them closely, and retain them for future reference.
To prevent fire or shock hazard, do not expose this sys-
tem to rain or moisture.
Heed Warnings — Follow all warnings on the product and in the operating instructions.
Cleaning — Unplug this product from the wall outlet before cleaning. Use only a damp cloth for
cleaning. Do not use liquid or aerosol cleaners.
CAUTION
Attachments — Do not use attachments/accessories not recommended by the product manufac-
turer, as they might create a hazard.
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
Water and Moisture — Do not use this product near water (for example, near a bathtub, washbowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool).
CAUTION
: TO REDUCE THE RISK OF
Accessories — Do not place this product on an unstable cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the
product. Follow the manufacturer's instructions for mounting, and use a recommended mounting
accessory.
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
Carts — Move the product on a cart carefully. Quick stops, excessive force, and
uneven surfaces may cause the product/cart to overturn.
Ventilation — Slots and openings in the cabinet provide ventilation, ensure reli-
able operation, and protect from overheating. Do not block or cover these open-
ings, and do not place the product on a bed, sofa, rug, or other similar surface. Do
not place the product in a built-in bookcase or rack unless it provides proper ven-
tilation as specified by the manufacturer.
This symbol is intended to alert you to the
presence of uninsulated dangerous voltage
within the system’s enclosure that might be of
sufficient magnitude to constitute a risk of
electric shock. Do not open the system’s
case.
Power Sources — Operate this product using only the power source indicated on its marking label.
If you are not sure of your home's power type, consult your product dealer or local power company.
Polarization — This product is equipped with a polarized AC line plug (a plug having one blade
wider than the other). This plug will fit in the power outlet only one way. This is a safety feature. If
you cannot insert the plug fully into the outlet, try reversing the plug. If the plug still doesn't fit, con-
tact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polar-
ized plug. If you need an extension, use a polarized cord.
This symbol is intended to inform you that im-
portant operating and maintenance instruc-
tions are included in the literature acc-
ompanying this system.
!
Power-Cord Protection — Route power-supply cords so they are not likely to be walked on or
pinched by items placed on or against them, paying particular attention to cords at plugs, conve-
nience receptacles, and the point where they exit from the product.
Lightning — For added protection for this product during a lightning storm, or when it is left unat-
tended and unused for long periods of time, unplug it from the wall outlet and disconnect the anten-
na or cable system. This will prevent damage to the product due to lightning and power-line surges.
CAUTION
Power Lines—Locate an outdoor antenna away from
Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles,
as this can result in a risk of fire or electric shock.
power lines.
Nonuse Periods—Unplug the receiver’s power cord
when you will not use it for extended periods.
Objects and Liquids — Never push objects of any kind into this product through openings, as they
may touch dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
Outdoor Antenna Grounding—If an outside antenna
or cable system is connected to the receiver, ground
the antenna or cable system so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA 80, provides information about proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-
discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See the
example below.
Servicing — Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service person-
nel.
Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qual-
ified service personnel under the following conditions:
•
•
•
•
When the power-supply cord or plug is damaged.
If liquid has been spilled or objects have fallen into the product.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operating instructions, as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified techni-
cian to restore the product to normal operation.
Antenna
Lead-In
Wire
•
•
If the product has been dropped or damaged in any way.
When the product exhibits a distinct change in performance.
Ground Clamp
Antenna
Replacement Parts — When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or having the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Discharge Unit
(NEC Section 810-20)
Electric
Service
Equipment
Grounding Conductors
(NEC Section 810-21)
Safety Check — Upon completion of service or repairs to this product, ask the service technician
to perform safety checks to determine that the product is in proper operating condition.
Grounding Clamps
Power Service Grounding
Electrode System
(NEC Article 250, Part H)
Wall or Ceiling Mount — The product should be mounted to a wall or ceiling only as recommended
by the manufacturer.
NEC -- National Electrical Code
Heat — The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that produce heat.
3
Contents
Preparing Your Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Positioning Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connecting Program Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using One Remote Control for More than One Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing the Remote Control’s Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the AC Power Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connecting to AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Demonstration Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Balance Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Muting the Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Tuning the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using FM Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Turning Off the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using Sleep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cassette Deck/VCR Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Using the VCR/TAPE 1 Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Using the TAPE 2 MONITOR Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Recording a Program Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Dubbing a Cassette Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Playing and Recording Video Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using Advanced Sound Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Sound Mode Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Returning Controls to Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
The FCC Wants You To Know . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Index to Features by Control Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4
Preparing Your Receiver
Caution: Make all the necessary connections before you plug in or turn on the receiver.
Where you place your speakers (not supplied) can make a noticeable difference
in your system’s sound. The guidelines in this section will help you choose the
best locations. After you use your receiver for a while, you might want to try dif-
ferent locations for your speakers.
Positioning Speakers
a
L
R
Between Speakers
Bass response depends largely on speaker location. For strong bass, place the
speakers in the corners of the room. If you want even stronger bass, place the
speakers directly on the floor. If the bass is too strong, move the speakers
slightly away from the corners of the room, or raise them 6 to 18 inches off the
floor. You can buy speaker stands at your local Radio Shack store.
Halfway Point
b
a=b
The distance between the speakers should be about the same as the distance
between the normal listening point and the point halfway between the speakers.
If you place the speakers too close together, you reduce the stereo separation.
If you place them too far apart, you reduce the bass effect and create a hole in
the middle of the sound.
Main Listening Area
Most speakers have a tweeter dispersion angle of about 60 degrees. Ideally,
your listening position should be just inside the overlap area of the tweeter dis-
persion. You can angle the speakers toward you for better stereo effect.
• Surround speakers generally sound
best if you position them above ear
level.
• To avoid interference with the picture
on a nearby TV, use magnetically
shielded speaker systems. This is par-
ticularly important for the center
speaker since it is usually located
closest to the TV.
To position your speakers for surround sound, place the A or B speakers at the
front of your listening area, and place the surround speakers behind or to the
sides of the listening point (see “Using Advanced Sound Options”). Also, place
the center speaker above, below, or behind the TV. Sound might not appear to
coincide with the picture if you place it beside the TV.
Right Front
Left Front
Center Channel
Listening
Area
Rear Channel
Rear Channel
5
Preparing Your Receiver
Connecting Speakers
Preparing the Speaker Wires
Speaker wire consists of two conductors (individual wires) encased in insulation
and is usually color-coded or marked with a ridge along one side so you can
identify each conductor. Use these markings as a guide to help you properly
connect the speakers to your receiver.
Follow these guidelines when you select
and connect speakers.
• Be sure you properly connect all
speakers.
Follow these steps to prepare the speaker wires.
• Do not connect two pairs of speakers
to a single set of terminals (A or B) at
the same time. When you use two
pairs of speakers, connect one set to
Speakers A
Speakers B
.
and one set to
• Realistic, Optimus, and other high-
quality speakers have color-coded
speaker terminals (red for positive
polarity and black for negative polar-
ity). Use these color-coded terminals
as a guide to help you properly con-
nect the speakers to the receiver.
• Use 16-gauge (or larger) speaker wire
for all speaker connections, and con-
sider possible speaker locations
before you decide how much speaker
wire you need.
1. Cut the speaker wires to the necessary length.
2. Separate the wires about 4 inches on each end.
3
3. Using a wire stripper, carefully strip about /4 inch of insulation from the
end of each conductor.
4. Twist the end of each conductor to secure any loose wire strands.
Surround
Speakers
Left
R
L
L
A
B
A
B
R
CENTER
SPEAKER
REAR
SPEAKERS
FRONT SPEAKERS
Center Speaker
Front B Speaker
Front A Speaker
Left
Left
6
Preparing Your Receiver
Connecting the A and B Speakers
Note: Be sure you connect the
receiver’s right and left positive (+) and
negative (–) terminals to the speaker’s
corresponding right and left positive (+)
and negative (–) terminals.
Follow these steps to connect the right speaker to the receiver’s right FRONT
SPEAKERS A terminals.
1. Press the receiver’s FRONT SPEAKERS A R (+) red lever and insert the
ridged or color-coded conductor’s end into the small hole. Pull back the
lever to secure the conductor.
2. Press the receiver’s FRONT SPEAKERS A R (–) black lever and insert the
other conductor’s end into the small hole. Pull back the lever to secure the
conductor.
3. Connect the ridged or color-coded conductor’s loose end to the right
speaker’s positive (+) terminal.
4. Connect the remaining loose conductor to the right speaker’s negative (–)
terminal.
Repeat Steps 1 through 4 to connect the left speaker to the receiver’s FRONT
SPEAKERS A L terminals.
Repeat this entire process to connect a second pair of speakers to the FRONT
SPEAKERS B terminals.
Connecting Surround-Sound Speakers
You can connect a pair of speakers to the receiver’s REAR SPEAKERS terminals
for surround-sound programs. Follow the steps in “Connecting the A and B
Speakers.”
Connecting the Center Speaker
The center speaker gives additional ambience to surround sound. Connect the
center speaker to the CENTER SPEAKER terminals. Follow the steps in “Con-
necting the A and B Speakers.”
Connecting Center Channel and Subwoofer Amplifiers
To increase the center channel’s output power, you can connect an amplifier to
the CENTER jack, as shown. Then connect the center channel speaker to the
amplifier.
Your receiver includes a line-level subwoofer output. Connecting a subwoofer to
your system dramatically extends bass response for incredible richness and
depth. When you listen to surround-sound programs, a subwoofer enhances
your home theater experience by realistically recreating the rumble of an earth-
quake, the bone-jarring percussion of a cannon, and more.
To use this output, simply connect it to an amplified subwoofer’s line-level input
or to an amplifier to which you have connected a subwoofer.
Radio Shack stores sell a variety of suitable subwoofers and amplifiers.
7
Preparing Your Receiver
You can connect up to five external program sources to your receiver.
Connecting Program Sources
OUT PUT
L
CD
R
L
FM
UNBAL
R
75
TO MONITOR TV
VIDEO OUT
IN
OUT
IN
GND
VIDEO
REC
PLAY
AM
L
IN
GND
L
OUT
R
LOOP
ANTENNA
R
TAPE2
MONITOR
VCR
/TAPE1
ANTENNA
PHONO
CD
LD
CONTROL
GND
L
R
Connecting a Turntable
Connect a turntable with a magnetic cartridge only. Some older turntables use a
ceramic-type cartridge that does not work with this system.
Use shielded audio cables with phono
connectors for all audio connections.
Connect the turntable’s left and right cables to the receiver’s left and right
PHONO
GND
jacks. Then connect the turntable’s ground wire to the receiver’s
terminal.
Connecting Cassette Deck(s)
VCR/TAPE 1
TAPE 2 MONITOR
and the
You can connect cassette decks to the
Note: If you place the cassette deck
directly above, below, or to the left of the
receiver, the receiver could interfere with
the cassette deck’s operation. If possi-
ble, position the cassette deck to the
right of the receiver or locate it away
from the receiver.
VCR/TAPE 1 IN
jacks. Connect the cassette deck’s output jacks to the
(audio) or
TAPE 2 PLAY
VCR/
jacks, and connect the input jacks of your cassette deck to
TAPE 2 REC
TAPE 1 OUT
(audio) or
jacks.
LD IN
You can connect a third cassette deck (for playback only) to the
jacks.
(audio)
Connecting a CD Player
To connect a CD player to the receiver, connect the CD player’s left and right
R CD
L
output jacks to the receiver’s and
input jacks.
8
Preparing Your Receiver
Connecting Video Sources
If you connect two video sources such as VCRs or laser disc players to your
receiver, you can use the receiver to switch between viewing the sources. You
can also use the receiver to easily record from the video sources to the source
connected to VCR/TAPE 1.
Note: If your VCR is monaural, use a Y-
adapter (available at your local Radio
Shack store) to connect the VCR’s audio
output to both the L and R audio inputs
on the receiver.
LD Player
Speaker
AUDIO
OUT
VIDEO
OUT
L
R
R
L
IDEO
IN
Power
Amplifie
IN
FM
UNBAL
75
TO MONITOR TV
VIDEO OUT
IN
OUT
IN
GND
VIDEO
R
R
L
L
R
L
CENTER
PRE OUT
REC
PLAY
AM
A
B
A
B
IN
L
GND
L
LOOP
ANTENNA
OUT
R
R
CENTER
SPEAKER
REAR
SPEAKERS
TAPE2
MONITOR
VCR
PRE OUT
FRONT SPEAKERS
AC OUTLET
ANTENNA
PHONO
CD
LD
/TAPE1
CONTROL
SUB
WOOFER
GND
VIDEO
IN
OUT
L
R
(REC)
IN
(PLAY)
OUT
VCR
Connect phono cables from a VCR’s audio outputs to the receiver’s VCR/TAPE 1
or LD IN (audio) jacks. Then connect phono cables from the receiver’s VCR/
TAPE 1 OUT (audio) jacks to the VCR’s audio input jacks.
Connect video cables from each video source’s video outputs to the receiver’s
VCR/TAPE 1 or LD VIDEO IN jacks. Then connect video cables from the
receiver’s VCR/TAPE 1 VIDEO OUT jack to the VCR’s video input.
Connecting a Video Monitor
The monitor (or TV with baseband video input) you connect to the VIDEO OUT
terminal can monitor any program you connect to the receiver’s VCR/TAPE 1 or
LD input jacks. Then connect a video cable from the receiver’s VIDEO OUT TO
MONITOR TV jack to the monitor’s video input.
9
Preparing Your Receiver
Connecting the Antennas
In many cities, the supplied indoor AM loop and FM antennas provide adequate
reception.
AM Antennas
Assemble the included antenna’s base by swinging the base in the direction of
the arrow and inserting the antenna’s bottom tabs into the base’s slot. Then
AM
GND
terminals (bottom two terminals).
attach the antenna wires to the
and
Place the antenna on a flat surface and rotate it for the best AM reception.
If the receiver is in a rack or on a shelf and there is no room for the AM loop
antenna, use two screws (not supplied) to mount the base on the wall or
another location as shown.
Notes:
• Keep the AM loop antenna connected even when you use another indoor
antenna or an outdoor AM antenna.
• Ensure the antenna does not touch the receiver or other metal objects.
• Do not place the antenna near a CD player, a personal computer, or a TV
set
FM
UNBAL
75
• If the wire between your AM loop antenna and receiver is too short, you
can add extra wire, available at your local Radio Shack store.
GND
AM Loop Antenn
AM
Ground
You can also use a Radio Shack shortwave antenna kit (Cat. No. 278-
758), which makes an excellent outdoor AM antenna.
GND
LOOP
ANTENNA
Connect the outdoor AM antenna wire to the receiver’s AM terminal, as shown.
r AM Antenna
FM
UNBAL
75
GND
AM
FM Antennas
FM UNBAL 75
Connect the supplied FM antenna to the
as shown.
Ω terminal and extend it
For better FM reception, you can also use a rabbit-ear TV antenna (for indoor
use only) or an outdoor VHF TV antenna. To connect the TV antenna to the
receiver, you need a VHF/UHF/FM splitter (not included). Radio Shack stores
carry a full line of quality outdoor antennas and antenna connection accesso-
ries.
Note: For the best results, use 75-ohm
coaxial cable to connect an outdoor
antenna to the receiver.
10
Preparing Your Receiver
For the best radio reception, use an outdoor antenna. Follow these steps to
connect an outdoor FM antenna to the receiver using 75Ω cable.
Warning: To prevent injury, read and fol-
low all cautions and warnings that
accompany the outdoor antenna.
Note: If your antenna has 300Ω twin-lead cable, consult your local Radio Shack
store for the correct adapter.
FM UNBAL 75
1. Disconnect the supplied FM antenna from the receiver’s
terminal.
Ω
2. With a stripping tool, remove about 11/2 inches of the cable’s outer insula-
tion to expose the cable’s shielding.
3. Fold back the insulation from the inner insulation.
4. Remove about 1 inch of the inner insulation from around the center wire.
FM
5. Pull the shielding to one side. Connect the center wire to the receiver’s
Caution: The cable’s shielding should
UNBAL 75
Ω terminal. Twist the shielding to secure any loose wire strands,
GND
only touch the
terminal.
GND
and connect it to the
terminal.
FM Outdoor Antenna
FM
UNBA
75
GND
AM
75 Coaxial Cable
GND
LOOP
ANTENNA
Note: Grounding is not necessary for reception, but we recommend it to avoid
damage from lightning when you use an outdoor FM antenna and for better FM
reception. Use a separate piece of thick polyvinyl insulated wire to connect the
GND
terminal to an earth ground such as a metal cold-water pipe.
Warning: Never connect a wire to a gas pipe for grounding since sparks might
ignite the gas.
11
Preparing Your Receiver
If you also have an Optimus professional series CD player, VCR, or cassette
CONTROL IN
so you can control all of your equipment with a single remote control. You can
also use the other component’s remote control by pointing it at the receiver’s
front panel.
Using One Remote Control
for More than One Unit
deck with the OSR mark, you can connect its
jack to the receiver
Note: When you plug the cable into a
CONTROL IN
component’s remote sensor does not
function.
component’s
jack, that
1. Connect each component to the receiver as shown in “Connecting Pro-
gram Sources.”
2. Connect the cable supplied with the CD player, VCR, or cassette deck
CONTROL
CONTROL OUT
between the receiver’s
CONTROL IN
jack and the other component’s
IN
IN
jack.
OUT
OUT
CONTROL
3. When you want to control more than one other component using the
CONTROL OUT CONTROL
receiver’s remote control, daisy-chain the
IN
and
connections as shown.
Receiver
Other Component
with OSR Mark
To the CONTROL IN jack
of Another Component
Having the OSR mark
Remote
Control
The remote control uses two AA batteries (not included). For the longest battery
life, we recommend Radio Shack’s alkaline batteries (Cat. No. 23-557).
Installing the
Remote Control’s Batteries
1. Press and open the battery
compartment cover.
2. Place two fresh AA batteries in
the compartment as indicated by
the polarity symbols (+ and –)
marked in the compartment.
Cautions:
• Use only fresh batteries of the recom-
mended size and type.
• Always remove old or weak batteries.
Batteries can leak chemicals that can
damage electronic circuits.
3. Replace the battery compartment
cover.
Note: If the remote’s range is reduced,
replace the batteries immediately.
12
Preparing Your Receiver
Your receiver has an AC power outlet that you can use to power an electronic
device, such as a turntable, cassette deck, VCR, and so on. This switched out-
let turns on and off with the receiver and provides a maximum of 100 Watts.
Using the AC Power Outlet
Caution: Do not connect appliances with
high power consumption, such as a
heater, iron, monitor, or TV, to this AC
outlet. Doing so can cause a risk of over-
heating and fire, and could damage the
receiver.
AC OUTLET
Before you plug in the receiver’s power cord, double check all other connec-
tions.
Connecting to AC Power
To power the receiver, plug the supplied power cord into a standard AC outlet.
The power cord’s plug is polarized and fits only one way.
Warning: To prevent electric shock, do
not use this polarized plug with an exten-
sion cord, receptacle, or other outlet
unless you can fully insert the blades to
prevent blade exposure.
R
R
L
L
A
B
FRONT SPEAKERS
AC OUTLET
RETURN
To see a demonstration of the receiver’s display, press and hold
while
Demonstration Display
turning on power. The receiver cycles through several demonstration displays.
To exit the demonstration mode, press any key.
13
Basic Operation
Note: The controls on the remote control work the same as the buttons on the
receiver’s front panel.
Warning: To prevent possible hearing
loss, turn VOLUME to MIN before you turn
on the receiver or change the program
sources. After you turn on the receiver or
change the program source, adjust VOL-
UME to a comfortable listening level.
Follow these steps to use the receiver.
1. Press POWER to turn on the receiver’s power. It takes about 5 seconds to
begin hearing sound.
2. Select the speakers.
FRONT SPEAKERS A
B
If you connected speakers only to the
(or ) ter-
SPEAKERS A (or B) to turn on only those speakers.
minals, press
FRONT SPEAKERS A
B
If you connected speakers to both the
and ter-
minals, do any of the following:
•
•
•
Press in SPEAKERS A or B to turn on either pair of speakers for a two-
speaker stereo effect.
Note: If you want to find out what a par-
ticular button or control is used for, see
Page 22 (for the remote control) or Page
30 (for the front panel) to find the page
where the button or control is described.
Press in SPEAKERS A and B to turn on both pairs of speakers for a
four-speaker stereo effect.
Press SPEAKERS A and B to the out position to silence all speakers
and listen privately with headphones.
3. Select a program source.
To tune to a radio station, see “Tuning the Radio” on Page 16.
TAPE 2 MONI-
To listen to signals from the component connected to
Note: If you select a source while TAPE 2
MONITOR is engaged, TAPE 2flashes
five times on the display, reminding you
to disengage the TAPE 2 MONITOR func-
tion.
TOR press TAPE 2 MONITOR so TAPE 2appears on the display.
,
TAPE 2 MONITOR
To listen to a source other than one connected to
,
be sure TAPE 2does not show on the display. If necessary, press TAPE
2 MONITOR so TAPE 2disappears.
Then press VCR/TAPE 1, LD (laser disc), CD, TUNER, PHONO, or repeat-
edly press FUNCTION on the remote control to display the desired pro-
gram source.
4. Adjust VOLUME clockwise to increase the volume and counterclockwise
to decrease it. Or, you can use MASTER VOLUME –/+ on the remote con-
trol.
5. Use the BASS and TREBLE controls to adjust the program’s tonal quality.
To enhance the bass level, press SUPER BASS.
6. Adjust BALANCE to suit your listening preferences. See “Balance Control”
on Page 15.
7. Press POWER to turn off the receiver.
14
Basic Operation
BALANCE
The
control lets you adjust the sound balance between the left and
Balance Control
right speakers. If you properly position the speakers and your listening area is
centered between them, the center control setting is usually best (see “Position-
ing Speakers” on Page 5).
BALANCE
For an unusual speaker placement, adjust
as follows:
to select the FM band.
until MONOappears. The sound is monaural instead of
TUNER
FM/AM
1. Select
. Then press
FM MONO
2. Press
stereo, so each speaker delivers the same output.
BALANCE
3. Turn
until you hear the sound coming equally from each
speaker when you are in the listening area.
FM MONO
4. Press
until MONOdisappears from the display.
MUTING
To temporarily mute the sound, press
on the remote control. MUTING
again to restore the audio level.
Muting the Receiver
Using Headphones
MUTING
appears. Press
1
To listen with headphones (not supplied), insert the headphones’ /4-inch plug
PHONES
A
into the receiver’s front panel
jack. To silence the speakers, set and
B SPEAKERS
to the out position and turn off any special sound options.
Listening Safely
To protect your hearing, note the following when using headphones.
• Set the volume to its lowest setting before you begin listening. After you
begin listening, adjust volume to a comfortable level.
• Do not listen at extremely high volume levels. Extended high-
volume listening can lead to permanent hearing loss.
• Once you set the volume, do not increase it. Over time, your ears adapt to
the volume level, so a volume level that does not cause discomfort might
still damage your hearing.
15
Basic Operation
Tuning the Radio
Your receiver offers three types of electronic tuning—manual, automatic, and
memory.
Manual and Automatic Tuning
Follow these steps to manualy or automatically tune to the stations.
TUNER
FM/AM
to select the desired band.
1. Press
. Then press
When you select the AM or FM radio band, the receiver tunes to and dis-
plays the frequency last selected in that band.
SELECT
2. Press
so FREQappears on the JOG MODEdisplay.
3. To manually tune the station, turn the multi-jog control or repeatedly press
TUNING +
–
or on the remote control to tune the desired station.
AUDIO/VCR
To automatically tune to the next higher or lower station, set
TUNING +
–
press and hold
or on the remote control until the stations start
to change. Then release the button.
Notes:
• TUNEDappears on the display when you tune to a strong station.
• STEREOappears on the display when FM broadcasts are received in
stereo and the receiver is not set to FM mono.
Memory Tuning
Memory tuning lets you instantly tune to a stored frequency. You can store up to
30 AM or FM frequencies in the receiver’s memory.
Follow these steps to store a station in a memory location.
TUNER
FM/AM
to select the desired band.
1. Press
. Then press
2. Using either manual or automatic tuning, select the frequency you want to
store.
Notes:
• If you store a frequency in a memory
that already contains a frequency, you
replace the previous frequency.
FM MONO
If desired, press
for FM monaural sound (see “Using FM Mono”
on Page 17). This setting is stored in the memory.
• If your receiver is disconnected from
AC power for several days, it loses all
the stored frequencies.
MEMORY
3. Press
. MEMORYappears for 5 seconds.
4. While MEMORYis on the display, turn the multi-jog control to select the
ENTER
memory number you want, then press
memory.
to store the frequency in
The frequency and memory number flash, then light steadily.
SELECT
To tune to a stored frequency, press
so STappears on the JOG MODE
STATION –/+
display, then turn the multi-jog control. You can use
on the remote
control to move to the next lower or higher memory. See “Using the Remote
Control” on Page 22.
16
Basic Operation
FM MONO
To receive FM stations in stereo, press
until MONOdisappears from
Using FM Mono
the display. STEREOappears on the display when you receive an FM broadcast
in stereo.
FM MONO
You can improve the reception of weak FM stations by pressing
until
MONOappears. This reduces noise while you listen to a weak FM station, but
you get monaural instead of stereo sound.
You can turn the display off so it does not bother you in a darkened room. Press
Turning Off the Display
DISPLAY OFF
. Only DISPLAY OFFappears on the display.
DISPLAY OFF
Press
again or press any button to restore the display.
The sleep function lets you set the receiver to turn off after 90, 60, or 30 min-
AUDIO/VCR AUDIO SLEEP
Using Sleep
(Remote Control Only)
utes. To start the timer, set
to
. Then repeatedly press
until the desired turn-off time appears. To cancel the timer, repeatedly press
SLEEP
until the sleep time disappears from the display.
17
Cassette Deck/VCR Features
You can connect two cassette decks to the receiver. Selecting either VCR/TAPE
1 or TAPE 2 MONITOR lets you hear the playback from the cassette deck you
connected to the receiver’s corresponding (VCR/TAPE 1, TAPE 2 MONITOR)
jacks.
Press VCR/TAPE 1. VCRappears on the display. You hear the playback from the
cassette deck or VCR you connected to the receiver’s VCR/TAPE 1 jacks.
Using the VCR/TAPE 1
Button
Press TAPE 2 MONITOR. TAPE 2appears on the display along with the last
program source you selected. You can hear playback or monitor a recording
from the cassette deck you connected to the receiver’s TAPE 2 MONITOR jacks.
Using the TAPE 2
MONITOR Button
The TAPE 2 REC jacks continue to output the previously selected source when
you press TAPE 2 MONITOR.
To return to the previous source, press TAPE 2 MONITOR again so TAPE 2dis-
appears.
Notes:
• If you press TAPE 2 MONITOR when the cassette deck is neither playing
nor recording, the receiver mutes the current audio source. To hear the
audio source, press TAPE 2 MONITOR until TAPE 2disappears from the
display.
• Do not press TAPE 2 MONITOR while you are recording on the deck con-
nected to TAPE 2 REC. If you do, the recording is interrupted for about 1
second.
The receiver sends the audio program source you select—VCR/TAPE 1, TAPE 2
MONITOR, LD, CD, TUNER, PHONO—to the VCR/TAPE 1 OUT (audio) and TAPE 2
MONITOR REC jacks.
Recording a Program Source
The VOLUME control does not affect the level of the signal going to the tape
decks.
18
Cassette Deck/VCR Features
You can copy, or dub, a cassette tape from one cassette deck to another.
Dubbing a Cassette Tape
You can use either deck as the playback or recording deck. However, if you
want to monitor the cassette deck during dubbing, use the deck connected to
VCR/TAPE 1
TAPE 2
until TAPE 2
the
jacks as the source, and the deck you connected to the
TAPE 2 MONITOR
jacks as the recording deck. Then press
appears on the display. See “Using the TAPE 2 MONITOR Button” on the previ-
ous page.
You can connect two video sources to the receiver. If you connect a VCR to the
Playing and Recording
Video Tapes
VCR/TAPE 1
audio and video jacks, you can copy video cassette tapes from one
VCR to another and monitor the dubbing process.
Playing a Video Cassette Tape
VCR/TAPE 1
To play a video tape, load the tape into the VCR connected to either
LD
VCR/TAPE 1
. Press the button (
LD
or ) that corresponds to the jack the
or
VCR is connected to. VCRor LDappears on the display. Follow the VCR’s
instructions to begin playback. If you connected a monitor to the receiver’s
TO
MONITOR TV
jack, you can view the program on that monitor.
Copying a Video Cassette Tape
Follow these steps to copy a video tape from one VCR to another.
LD
1. Load the tape you want to copy into a VCR connected to
.
2. Load a blank tape (or one you want to record over) in the VCR connected
VCR/TAPE 1
to the
jacks.
LD
3. Press
.
4. Begin recording and playback on the VCRs.
19
Using Advanced Sound Options
Your receiver has four special sound options: Dolby Pro-Logic Surround, Dolby
3CH Logic, Studio-Effect Surround, and Simulated Surround. These special
options enhance a program source.
Notes:
• To get the full benefit from programs encoded with Dolby Surround
Sound, you need a stereo VCR.
• Dolby Surround does not operate correctly if the signal passes through a
graphic equalizer. If you connected an equalizer to the TAPE 2 MONITOR
jacks, do not select TAPE 2 MONITOR when you listen to Dolby Surround
signals.
To activate Dolby Pro-Logic Surround or Dolby 3CH Logic, press its button. For
studio effect, simulated surround, or arena effect, press SFC MODE until the
desired option appears on the display. On the remote control, press 3CH LOGIC
to select Dolby 3CH Logic Sound and use SURR MODE for other sound options.
Dolby Pro-Logic Surround
Dolby Pro-Logic Surround puts you in the middle of the action. The center- and
rear-channel speakers add incredible realism by directing the sound to the
appropriate speakers, making you feel like you are really there. You can find
hundreds of movies, television shows, and compact discs produced with Dolby
Surround.
Dolby 3CH Logic
Dolby 3CH Logic produces a more spacious sound field than is possible with
ordinary stereo playback by combining the front and rear speaker sounds.
Select this mode when you play a Dolby Surround Sound program and do not
have rear speakers. The rear channel’s sound is sent to the front left and right
speakers.
Studio Effect
Studio Effect gives the effect of listening in a recording studio. The front speak-
ers provide normal stereo, and the rear speakers provide a subtly reverberated
sound. Select this mode when you listen to sources not encoded with Dolby
Surround.
Simulated Surround
Simulated Surround simulates a surround effect when you listen to a monaural
(mono) source.
20
Using Advanced Sound Options
Center Mode Setting
Sound Mode Adjustments
(Remote Control Only)
The center mode setting affects the center channel’s bass signals. It operates
only when you select the Dolby Pro-Logic Surround or Dolby 3CH Logic mode.
AUDIO VCR
AUDIO
CENTER
. Each time you press
Slide
•
on the remote control to
Notes:
MODE
on the remote control, the setting changes, and the receiver’s corre-
• If you do not use a center speaker, the
monaural signals are only reproduced
if you select PHANTOM.
sponding indicator lights: NORMAL- WIDE- PHANTOMfor Dolby Pro-Logic Sur-
round; NORMAL- WIDEfor Dolby 3CH Logic.
NORMAL—Select this mode if you use a small center speaker. The front left and
right speakers play the center-channel bass sounds.
• You cannot select PHANTOM in the
Dolby 3CH Logic Sound mode.
WIDE—Select this mode if you use a medium or large center speaker. The cen-
ter speaker plays the center-channel bass sounds.
PHANTOM—Select this mode if you have no center speaker. All center-channel
sound comes from the front left and right speakers.
Test Tone
The test tone feature provides a test tone that lets you balance the signal levels
between all your speakers. See “Center Level” and “Rear Level.”
To activate the test tone, select one of the surround sound modes and set
AUDIO/VCR
VCR
TEST TONE
. Then press . The receiver sounds
on the remote to
a 2-second tone from the front left, center, front right, and rear speakers, in
sequence. The center test tone sounds only when you select the Dolby Pro-
Logic Surround or Dolby 3 CH Logic Sound mode.
In the Dolby 3CH Logic Sound mode, the receiver sounds a 2-second tone from
the left, center, and right speakers, in sequence.
TEST TONE
Press
again to turn off this feature.
Center Level
AUDIO VCR
AUDIO
– CENTER +
. Then press to adjust the center
Slide
•
to
speaker sound level while in the Dolby Pro-Logic Surround or Dolby 3CH Logic
mode.
Notes:
VOLUME
• Use the
control to adjust the
overall sound level.
Rear Level
• Set the center mode to a selection
other than PHANTOM before adjusting
the center level.
AUDIO VCR
VCR
– REAR +
. Then press to set the rear speakers’ sound
Slide
•
to
level while in the Dolby Pro-Logic Surround or Simulated Surround mode.
Delay Time
In the Simulated Surround and Dolby Pro-Logic Surround modes, the receiver
slightly delays the sound going to the rear speakers. You can change the delay
time from 16 to 30 milliseconds (ms) in 2 ms steps. Adjust this for the best sur-
round effect.
Notes:
• For Dolby Pro-Logic Surround, the
delay is preset to 20 mS.
• The delay time does not affect the Stu-
dio Effect mode.
AUDIO VCR VCR
to
DELAY TIME
to change the delay
Slide
•
. Then press and hold
time. The receiver displays the selected time.
21
Using the Remote Control
The remote control works up to a distance of about 23 feet, and within a 30-
degree angle on either side of the receiver. Point the control at the receiver’s
front panel and press the desired button(s).
Many buttons on the remote control work the same as buttons on the receiver’s
front panel. Use these buttons exactly as you would use the corresponding but-
tons on the receiver.
AUDIO/VCR Switch
The remote control can also control other compatible audio/video components
when you connect them to the receiver’s CONTROL OUT jack. Set the switch to
AUDIO to control audio components such as CD players or cassette decks. Set
the switch to VCR to control video components such as a VCR.
When you set the switch to VCR, dual-function buttons control the function
marked in gold next to the button. For example, the button marked CENTER
MODE and TEST TONE operates as the center mode adjust when you set the
switch to AUDIO and as the delay time function when you set the switch to VCR.
Receiver/Amplifier Section
FUNCTION
Selects a program source (VCR/Tape 1, LD, CD, tuner, or
FUNCTION
phono). Repeatedly press
until the display shows
your desired program source. See Page 14.
Adjusts the system’s volume. See Page 14.
Selects among the three center mode settings with
– MASTER VOLUME +
CENTER MODE
AUDIO
/
VCR
AUDIO
. See Page 21.
set to
– CENTER +
– REAR +
Controls the relative volume of the center speaker with
AUDIO VCR AUDIO
/
set to
. See Page 21.
Controls the relative volume of the rear speakers with
AUDIO VCR VCR
/
set to
. See Page 21.
TEST TONE
DELAY TIME
AUDIO VCR
set to
Sounds test tones from each speaker with
VCR
/
. See Page 21.
Sets the rear-channel delay for Dolby Pro-Logic Surround
AUDIO VCR
set to
and Simulated Surround programs with
VCR
/
. See Page 21.
SURR MODE
SLEEP
Selects between Dolby Pro-Logic Surround or Simulated Sur-
round sound. See Page 20.
Sets the receiver to turn off after 90, 60, or 30 minutes with
AUDIO VCR
AUDIO
. To start the timer, repeatedly
/
set to
SLEEP
press
appears. To cancel the timer, repeatedly press
until the desired turn-off time ( )
90 60 30
,
, or
SLEEP
until
the sleep time disappears from the display. See Page 17.
RECEIVER POWER
RETURN
Turns the receiver on and off. See Page 14.
Returns the receiver to its default settings. See Page 27.
Selects Dolby 3CH Logic. See Page 20.
3CH LOGIC
TAPE 2 MONITOR
Switches the receiver to monitor the source connected to the
TAPE 2 MONITOR
jacks. See Page 18.
22
Using the Remote Control
MUTING
Silences the receiver. Press again to restore the sound to its
previous level. See Page 15.
– TUNING +
Tunes to radio stations with AUDIO/VCR set to AUDIO. See
Page 16.
Manual Tuning: Press once to select the next higher or
lower frequency. Or, press and hold down to rapidly change
frequencies.
Automatic Tuning: To search for the next higher or lower
station, release + TUNING –when the frequency starts to
change. The receiver searches up or down the band until it
finds a strong station.
– STATION +
Press to move the next higher or lower memory location with
AUDIO/VCR set to AUDIO. See Page 16.
CD Player Section
CD POWER
Turns the CD player on and off (only for CD players having
the CONTROL IN/OUT feature).
|
and
|
Returns to the beginning of the current track or advances to
the next track.
– DISC SELECT +
Selects discs in a multi-play CD changer.
Note: Some CD players might not be selected by DISC
SELECT.
Plays the CD.
Stops playback.
23
Using the Remote Control
Tape/VCR Section
Before operation:
• Set AUDIO/VCR to AUDIO for a cassette deck or to VCR for a VCR.
• For a cassette deck, select TAPE 2 MONITOR or VCR/TAPE 1.
• For a dual cassette deck, select DECK 1 or DECK 2. If you use a single
cassette deck, press DECK 2.
Press to start normal play.
Press to play the reverse side of an auto-reverse cassette
deck.
Press to cancel the current function.
and
For a cassette deck, lets you quickly locate and play the
beginning of recorded material during play.
When the tape is stopped, lets you rapidly search forward or
backward to locate a specific section of the tape.
For a VCR, lets you rapidly view a tape either forward or
backward.
DECK 1/DECK 2
TAPE POWER
– VCR CH +
TV/VCR
Selects Deck 1 or Deck 2 when you use a dual cassette deck
with AUDIO/VCR set to AUDIO.
Turns on the connected VCR with AUDIO/VCR set to VCR;
turns on the cassette deck with AUDIO/VCR set to AUDIO.
Moves to the next higher or lower channel with AUDIO/VCR
set to VCR.
Selects between normal TV viewing and VCR input with
AUDIO/VCR set to VCR.
TAPE SELECT
Selects cassette 1 to 6 for a multi-cassette changer.
24
Troubleshooting
If the receiver is not working as it should, the following suggestions might help. If you follow the suggestions in this chart and
the receiver still does not work properly, contact your local Radio Shack store for assistance.
Problem
Cause
Solution
Power does not turn on.
• Power cord is disconnected.
• Protection circuit is activated.
• Plug in the power cord.
• Unplug the power cord, then plug it in
again.
• Static discharge has affected control. • Unplug the power cord, then plug it in
again. (If static electricity is a prob-
The receiver does not respond to
button presses.
lem, try to use the remote control as
much as possible.)
No sound.
• Incorrect connections.
• Check and correct the connections.
• Press MUTING.
• The mute function is activated.
• The volume is turned down.
• Speaker wires are disconnected.
• Neither set of speakers is selected.
• Turn up the volume.
• Connect the speaker wires.
• Press in SPEAKERS A or B.
No picture when you select a video
source.
• The selected video source is not set • Correct the problem with the selected
correctly.
video source.
• Incorrect connections.
• Station not correctly tuned.
• Antenna not connected.
• Correct the connections.
• Tune to a stronger station.
• Connect the antenna.
High noise level.
• FM antenna still coiled or is not point- • Stretch both ends of the antenna taut
ing in the correct direction. and reposition the antenna.
• AM loop antenna not pointing in the • Adjust the AM loop antenna.
correct direction.
• Noise is coming from another electri- • Try using an AC line noise filter to
cal appliance.
reduce the noise.
Tuning does not automatically stop
when searching for FM stations.
• Stations are too weak.
• Use a better antenna.
Cannot make copies of video tapes.
• Tapes are protected by a copy • You cannot make a good copy.
restriction method.
• Video connections are incorrect.
• Check and correct the connections.
Press RETURN to return the controls to the following settings.
Returning Controls to
Factory Defaults
Tape 2 Monitor
Source
Off
TUNER
On
Speakers A
FM or AM (Set to the last-tuned frequency. If the
receiver cannot receive the frequency, it starts
searching for the next strong station.)
Band
Surround Mode
Muting
Off
Off
Off
Super Bass
25
Care and Maintenance
Your STAV-3370 Digital Synthesized A/V Surround Receiver is an example of superior design and craftsmanship. The following
suggestions will help you care for the receiver so you can enjoy it for years.
Keep the receiver dry. If it gets wet, wipe it dry immediately. Liquids can contain
minerals that can corrode the electronic circuits.
Handle the receiver gently and carefully. Dropping it can damage its circuit
boards and can cause the receiver to work improperly.
Use and store the receiver only in normal temperature environments. Tempera-
ture extremes can shorten the life of electronic devices, damage batteries, and
distort or melt plastic parts.
Keep the receiver away from dust and dirt, which can cause premature wear of
parts.
Wipe the receiver with a damp cloth occasionally to keep it looking new. Do not
use harsh chemicals, cleaning solvents, or strong detergents to clean the
CLEANER
receiver.
Use only fresh batteries of the recommended size and type in the remote con-
trol. Always remove old or weak batteries. They can leak chemicals that can
destroy electronic circuits.
Modifying or tampering with your receiver’s internal components can cause a malfunction and might invalidate the receiver’s
warranty and void your FCC authorization to operate it. If the receiver is not operating as it should, take it to your local Radio
Shack store for assistance.
26
The FCC Wants You To Know
Your receiver might cause radio or TV interference even when it is operating
properly. To determine whether your receiver is causing the interference, turn off
your receiver. If the interference goes away, your receiver is causing it. Try to
eliminate the interference by:
• Moving your radio or TV away from the receiver
• Connecting your receiver to an outlet that is on a different electrical circuit
from the radio or TV
• Contacting your local Radio Shack store for help
If you cannot eliminate the interference, the FCC requires that you stop using
your receiver.
27
Specifications
Amplifier
Front Channel Average Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Watts per Channel into 8 Ohms
From 20 to 20,000 Hz,
With No More than 0.09% Total Harmonic Distortion
Measured Pursuant to the Federal Trade Commission’s
Trade Regulation Rule on Amplifier Output Power Claims
Front Channel Surround Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Watts per Channel
Center Channel Surround Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 Watts
Continuous Rear Surround Power Output . . . . . . . . . . . . . . . . . . . . . . . . . 100 Watts per Channel (1 kHz, 0.8% THD, 8 Ohms)
Dynamic Power Output (2 Ohms/4 Ohms/8 Ohms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 Watts/250 Watts/150 Watts
Input Sensitivity/Impedance
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8 mV/47 kOhms
CD, LD, VCR/TAPE 1, Tape 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/47 kOhms
Phono Overload Level (0.1% THD, 1 kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mV
Frequency Response
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .20 Hz to 20,000 Hz ±0.3 dB
CD, LD, VCR/TAPE 1, TAPE 2 Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hz to 100,000 Hz +0/–3 dB
Output Level/Impedance
VCR/TAPE 1 REC, Tape 2 Monitor REC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/2.2 kOhms
Tone Controls
Bass. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±8 dB (150 Hz)
Treble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±8 dB (10 kHz)
Super Bass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+8 dB (80 Hz)
Signal-to-Noise Ratio (IHF, Short Circuited, A Network)
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 dB
CD, LD, VCR/TAPE 1, Tape 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 dB
Signal-to-Noise Ratio (EIA, at 1 Watt, 1 kHz)
Phono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . 77 dB
CD, LD, VCR/TAPE 1, Tape 2 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 dB
Video Section
Input Sensitivity/Impedance VCR/TAPE 1, LD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Volt Peak-to-Peak/75 Ohms
Output Level/Impedance VCR/TAPE 1, Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Volt Peak-to-Peak/75 Ohms
Frequency Response VCR /TAPE 1, LD Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hz to 7MHz +0/–3 dB
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB
Crosstalk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB
28
Specifications
FM Tuner
Frequency Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87.5 to 108 MHz
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mono: 11.2 dBf, IHF (1.0 µV/75 Ohms)
50 dB Quieting Sensitivity
Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.8 dBf (1.9 µV/75 Ohms)
Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38.6 dBf (23.3 µV/75 Ohms)
Signal-to-Noise Ratio
Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 dB (at 85 dBf)
Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 dB (at 85 dBf)
Distortion Stereo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5% (1 kHz)
Alternate Channel Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 dB (400 kHz)
Stereo Separation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 dB (1 kHz)
Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Hz to 15 kHz (±1 dB)
Antenna Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Ohms Unbalanced
AM Tuner
Frequency Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 to 1700 kHz
Sensitivity (IHF, Loop Antenna) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 µV/m
Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 dB
Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 dB
General
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Volts AC, 60 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 Watts, 500 VA (UL)
AC Outlet Ratings Switched . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Total 100 Watts (0.8 Amps) Maximum
Dimensions (HWD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61/8 × 169/16 × 1113/16 Inches
(155 × 420 × 300 mm)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 lbs, 10 oz (8 kg)
Specifications are typical; individual units might vary. Specifications are subject to change and improvement without notice.
29
Index to Features by Control Name
This table lists the control and indicator names found on the front of your receiver, along with the page number where the con-
trol or indicator is discussed. To find a description for the buttons on the remote control, see “Using the Remote Control” on
Page 22.
Control
Page
BALANCE
BASS
15
14
CD
14
DISPLAY OFF
FM MONO
FM/AM
17
17
16
LD
14
MEMORY
MULTI-JOG
NORMAL
PHANTOM
PHONES
PHONO
16
16
21
21
15
14
POWER
RETURN
SELECT
SFC MODE
14
25
16
20
SPEAKERS A and B
SUPER BASS
TAPE 2 MONITOR
TREBLE
14
14
14, 18
14
TUNER
15
TUNING
23
VCR/TAPE 1
VOLUME
14, 18
14
WIDE
21
30
Notes
31
RADIO SHACK LIMITED WARRANTY
This product is warranted against defects for 2 years from date of purchase from Radio
Shack company-owned stores and authorized Radio Shack franchisees and dealers.
Within this period, we will repair it without charge for parts and labor. Simply bring your
Radio Shack sales slip as proof of purchase date to any Radio Shack store. Warranty
does not cover transportation costs. Nor does it cover a product subjected to misuse or
accidental damage.
EXCEPT AS PROVIDED HEREIN, RADIO SHACK MAKES NO EXPRESS WARRAN-
TIES AND ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURA-
TION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. Some states
do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limi-
tation(s) or exclusion(s) may not apply to the purchaser.
This warranty gives you specific legal rights and you may also have other rights which vary from
state to state.
We Service What We Sell
9/94
RADIO SHACK
A Division of Tandy Corporation
Fort Worth, Texas 76102
<ARB1484-A>
7A5
Printed in Japan
|