Panasonic Smoke Alarm 1735 User Manual

Fire alarm systems  
Alert annunciation units  
1735 and 1736  
Control and indicating unit for alert annunciation  
Compact size  
Acknowledge, indicating that the AA  
alarm has been acknowledged.  
Alert annunciation unit  
When the Alert Annunciation function shall  
be used in the systems EBL512 & EBL128  
an AA unit is required to present the AA  
alarms and for the related manoeuvres, i.e.  
to acknowledge / reset the alarms. For a  
detailed description of the AA function, see  
Planning and Operating instructions for the  
system respectively.  
The unit has the following push buttons:  
Alarms queued, used to scroll amongst  
the alarms.  
Acknowledge, used to acknowledge an  
AA alarm and hereby also silence the  
buzzer.  
Reset, used to reset an AA alarm.  
Point or zone alarm presentation is as in the  
c.i.e. it is connected to. When there are  
queued alarms in the system, you can scroll  
amongst them. All or selected alarms will  
be presented in the unit's display (LCD,  
2x40 characters with back-light). A user  
definable text message will be presented  
together with each alarm, if programmed in  
the c.i.e. Furthermore, > 617 texts can for  
selected alarms be stored in the unit and will  
in that case be shown, instead of the texts  
sent from the c.i.e. for these alarms. A built-  
in buzzer will sound to indicate a not  
acknowledged AA alarm. The unit is power  
supplied via the c.i.e. or ext. power supply.  
1735 has the designation texts in Swedish.  
1736 has a neutral front for other languages,  
see the opposite side of this page. (This  
front also holds one extra LED & two extra  
push buttons.)  
Compact size  
The compact size enclosure is made of grey  
high impact ABS. Fitted with a supple-  
mentary "O" ring gasket, it will comply with  
IP61, in respect of dust and moisture. The  
unit has no door, i.e. the front is accessed  
directly, when required. The push buttons  
are disabled until they are supposed to be  
used. The unit shall be wall mounted. Two  
compression glands are attached.  
LEDs, push buttons etc.  
The unit has the following LEDs:  
SW mode and address setting  
The display and the push buttons are used to  
set the SW mode and address.  
Fire and Alarms queued, indicating fire  
alarm / AA alarm.  
Operation, indicating that the AA  
function is enabled in the system.  
Normally a time channel is used to  
enable this function.  
Fire brigade alerted, indicating that the  
"Fire brigade tx" output is activated in  
the c.i.e. because:  
The SW modes are described on the  
opposite side of this page.  
Product application  
The units are intended for indoor use and in  
dry premises. They are intended to be used  
in the systems EBL512 & EBL128. An  
External FBP / DU interface board 1587 is  
required in the EBL512 c.i.e. and a 4552  
Transceiver component in the EBL128 c.i.e.  
- the activated alarm is not an AA alarm  
- the AA function has been ended, e.g.  
the acknowledge or investigation time  
has run out, etc.  
Panasonic Electric Works Fire & Security Technology Europe AB  
Citadellsvägen 23, SE-211 18 Malmö, Sweden  
Tel: +46 (0)40 697 70 00 • Fax: +46 (0)40 697 70 99  
 

Miller Electric Welder Spoolmate 250 User Manual
Milwaukee Work Light worklight User Manual
MTD Chipper 242 640 000 User Manual
Murphy Switch WDU 0277 User Manual
Nady Systems Headphones HM 1 User Manual
Nikon Camcorder L120 User Manual
Nintendo Video Game Controller BB 7556 User Manual
NordicTrack Home Gym NTTL09710 User Manual
Oregon Scientific Games 086 003875 034 User Manual
Palsonic Computer Monitor TFTV930 User Manual