Electronic Modular Switching System
Please read this manual before connecting the
Electronic Modular Switching System.
S
WITCHING SYSTEM
POW
ER
MODEL
KX-T206E
Important Information
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of
5 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark
or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is
replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN
YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF
AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS
INSERTED INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.
WARNING : THIS APPLIANCE MUST BE EARTHED.
IMPORTANT : The wires in this mains leads are coloured in accordance with the following
code:
Green-and-yellow: Earth
Blue:
Brown:
Neutral
Live
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows.
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the
plug which is marked with the letter E or by the safety earth symbol
GREEN-AND-YELLOW.
or coloured GREEN or
The wire which is coloured BLUE must be connected to the terminal in the plug which is
marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is
marked with the letter L or coloured RED.
How to replace the fuse : Open the-fuse compartment with a screwdriver and replace the fuse
and fuse cover.
3
Important Information
This equipment should be used on PSTN lines requiring 2-wire Loop calling unguarded clearing
with Loop Disconnect or DTMF address signalling.
The equipment must be connected to direct extension lines and a payphone should not be
connected as an extension.
Operation in Power Failure
In the event of a power failure, CO2 is connected to extension 22 automatically.
• Set the Dialling Mode (Tone or Pulse) of your telephone, according to the CO line.
• 999 and 112 can be dialled on the apparatus for the purpose of making outgoing calls to the BT
emergency (999) and (112) service.
Satisfactory performance can not be guaranteed for every allowed combination of host and
subsidiary apparatus.
999 and 112 can be dialled on the apparatus after accessing the CO line for the purpose of
making outgoing calls to the BT emergency (999) and (112) service.
During dialling, this apparatus may tinkle the bells of other telephones using the same line. This
is not a fault and we advise you not to call Fault Repair Service.
‘Prevention of access by user. This apparatus is intended to be accessible only to authorized
personnel. This apparatus must be installed in a locked room or similar environment, such that
user access is prevented. Failure to prevent such user access will invalidate any approval given
to this apparatus.’
Caution:
Do not push the PAUSE button more than twice following the initial access digit (or digits).
Failure to comply with this requirement may result in unsatisfactory operation.
Notice:
This PBX should only be used on B•T lines on which specific BT services or facilities are
provided.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according
to the manufacturer's instructions.
4
Precaution
• Keep the unit away from heating appliances and electrical noise generating devices such as
fluorescent lamps, motors and television. These noise sources can interfere with the perform-
ance of the Electronic Modular Switching System.
• This unit should be kept free of dust, moisture, high temperature (more than 40˚C/104˚F) and
vibration, and should not be exposed to direct sunlight.
• Never attempt to insert wires, pins, etc. into the vents or other holes of this unit.
• If there is any trouble, disconnect the unit from the telephone line. Plug the telephone directly
to the telephone line. If the telephone operates properly, do not reconnect the unit to the line
until the trouble has been repaired. If the telephone does not operate properly, chances are
that the trouble is in the telephone system, and not in the unit.
• Do not use benzine, thinner, or the like, or any abrasive powder to clean the cabinet. Wipe it
with a soft cloth.
WARNING
THIS UNIT MAY ONLY BE INSTALLED AND SERVICED BY QUALIFIED SERVICE
PERSONNEL.
WHEN A FAILURE OCCURS WHICH RESULTS IN THE INTERNAL PARTS BE-
COMING ACCESSIBLE, DISCONNECT THE POWER SUPPLY CORD
IMMEDIATELY AND RETURN THIS UNIT TO YOUR DEALER.
DISCONNECT THE TELECOM CONNECTION BEFORE DISCONNECTING THE
POWER CONNECTION PRIOR TO RELOCATING THE EQUIPMENT, AND
RECONNECT THE POWER FIRST.
THIS UNIT IS EQUIPPED WITH AN EARTHING CONTACT PLUG. FOR SAFETY
REASONS THIS PLUG MUST ONLY BE CONNECTED TO AN EARTHING CON-
TACT SOCKET WHICH HAS BEEN INSTALLED ACCORDING TO REGULATIONS.
THE POWER SOCKET WALL OUTLET SHOULD BE LOCATED NEAR THIS
EQUIPMENT AND BE EASILY ACCESSIBLE.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR ANY TYPE OF MOISTURE.
73/23/EEC
89/336/EEC
92/31/EEC
93/68/EEC
5
Table of Contents
Specifications ....................................................................................................................... 7
Before Installation............................................................................................................... 8
Unpacking............................................................................................................................ 9
Name and Location ............................................................................................................. 9
Wall Mounting .................................................................................................................... 10
Opening Front Cover.......................................................................................................... 10
Frame Ground Connection ................................................................................................ 10
System Connection Diagram ............................................................................................. 11
CO Line Connection ........................................................................................................... 12
Extension Connection ......................................................................................................... 13
Paralleled Telephone Connection ...................................................................................... 14
Installation of Optional Card and Unit ............................................................................ 15
Installation of Lightning Protectors .................................................................................. 17
Power Failure Transfer ...................................................................................................... 19
Starting the System ............................................................................................................. 19
General Programming Instructions .................................................................................. 20
System Programming ......................................................................................................... 21
System Speed Dialling Number Set................................................................................... 21
Dial Type Selection ............................................................................................................ 21
Outgoing Permitted CO1 Assignment (Day/Night) ........................................................... 21
Outgoing Permitted CO2 Assignment (Day/Night) ........................................................... 22
CO1 Ringing Assignment (Day/Night).............................................................................. 22
CO2 Ringing Assignment (Day/Night).............................................................................. 22
Doorphone Assignment (Day/Night) ................................................................................. 23
Toll Restriction (TRS) – Class Assignment (Day/Night) .................................................. 23
TRS Denied Code (CLASS 2, 3) ....................................................................................... 24
TRS Denied Code (CLASS 3) ........................................................................................... 24
OGM Recording ................................................................................................................ 24
OGM Play .......................................................................................................................... 25
Fax Connection .................................................................................................................. 25
CO1 Delayed Ringing Assignment .................................................................................... 25
CO2 Delayed Ringing Assignment .................................................................................... 26
Delayed Ringing Count Selection...................................................................................... 26
TRS Excepted Code ........................................................................................................... 26
Door Opener Assignment................................................................................................... 27
Day/Night Switching Mode ............................................................................................... 27
Day/Night Starting Time.................................................................................................... 27
System Data Clear ............................................................................................................. 27
Other programs .................................................................................................................. 28
Least Cost Routing (LCR) Programs ................................................................................. 30
Tone / Ring Tone ................................................................................................................. 32
Programming Tables........................................................................................................... 34
Templet ................................................................................................................................ 39
6
Specifications
General Descriptions
1. Capacity .................................... CO line
Extension
2
6
2. Control Method ......................... Stored Program CPU: 8 bits CPU
Control ROM: 64 KB, Control RAM: 8 KB
3. Switching Method ..................... Space Division CMOS Crosspoint Switch
4. Power Supplies ......................... Primary
Secondary
AC 110–240 V, 50/60 Hz
Circuit Volt: +5V, +15 V, +30 V
Power Failure CO 2 assigned to extension 22
5. Dialling
Outward
Internal
Dial Pulse
Tone Dial
Dial Pulse
Tone Dial
10 PPS
10 PPS, 20 PPS
Mode Conversion
DP-DTMF, DTMF-DP
6. Connector .................................. CO
Extension
Doorphone
4-pin connector
4-pin connector
4-pin connector
7. EXT Connection ....................... Cable
1 pair wire (single line telephone)
2 pair wire (proprietary telephone)
8. Intercom paths........................... 2 (including the doorphone path)
Characteristics
1. Station Loop Limit .................... Proprietary telephone
40 ohms
600 ohms including set
20 ohms
Single line telephone
Doorphone
2. Minimum Leak Resistance ....... 15000 ohms
3. Maximum Number of Station
Instruments per line .................. 1 (proprietary telephone) or 3 (single line telephone)
4. Ring Voltage.............................. 90 Vrms at 25 Hz depends on Ringing Load
5. Primary Power .......................... AC 110–240 V, 50/60 Hz, 0.5 A maximum
6. Central Office Loop Limit ........ 1600 ohms maximum
7. Environmental Requirements ... 0–40˚C, 10%–90% (Humidity)
7
Before Installation
Please read the following notes concerning installation and connection before installing the
system.
Safety Installation Instructions
When installing telephone wiring, basic safety precautions should always be followed to reduce the risk
of fire, electric shock and injury to persons, including the following:
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
4. Use caution when installing or modifying telephone lines.
Installation Precautions
This set is exclusively made for wall mounting only. Avoid installing in the following places. (Doing so
may result in malfunction, noise, or discoloration.)
1. In direct sunlight and hot, cold, or humid places. (Temperature range: 0˚C-40˚C/32˚F-104˚F)
2. Sulfuric gases produced in areas where there are thermal springs, etc. may damage the equipment
or contacts.
3. Places in which shocks or vibrations are frequent or strong.
4. Dusty places, or places where water or oil may come into contact with the unit.
5. Near high-frequency generating devices such as sewing machines or electric welders.
6. On or near computers, telexes, or other office equipment, as well as microwave ovens or air
conditioners. (It is preferable not to install in the same room with the above equipment.)
7. Install at least 1.8 m (6 feet) from radios and televisions. (both the main unit and a proprietary
telephone)
8. Do not obstruct area around the main unit (for reasons of maintenance and inspection – be
especially careful to allow space for cooling above and at the sides of the main unit).
Wiring Precautions
Make sure to keep the following instructions when wiring.
1. Do not wire the telephone cable in parallel with an AC power source, computer, telex, etc. If the
cables are run near those wires, shield the cables with metal tubing or use shielded cables and
ground the shields.
2. If cables are run on the floor, use protectors or the like to protect the wires where they may be
stepped on. Avoid wiring under carpets.
3. Avoid using the same power supply outlet for computers, telexes, and other office equipment.
Otherwise, the KX-T206’s system operation may be interrupted by the induction noise from such
equipment.
4. Please use one pair telephone wire for extension connection of (telephone) equipment such as
standard telephones, answering machines, etc., except proprietary telephones (KX-T7130,
KX-T7020, KX-T7050, etc.).
5. The AC cord must be plugged off during wiring. After all the wirings are completed, plug the AC
cord into an AC outlet.
6. Mis-wiring may cause the system to operate improperly.
7. If an extension does not operate properly, disconnect the telephone from the extension line and then
connect again, or plug off the AC cord of the system and then on again.
8. The KX-T206 is equipped with a 3-wire grounding type plug. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do
not defeat the purpose of the grounding-type plug.
9. Use twisted pair cable for CO line connection.
10. CO lines should be installed with lightning protectors. For details, see pages 17 and 18.
8
Unpacking
• Main Unit ............................. one
• AC Cord ............................... one
• Screw and Washer ................ three
• 4-pin Plug ............................. eight
Name and Location
Overview of the Main Unit
S
WITCHING SYSTEM
AC Inlet
POW
ER
Power Indicator
Inside View of the Main Unit
Door Opener Connector
Cable Holders
DOOR
OPENER
Extension 4-pin Jacks
EXTN.
5
EXTN.
6
EXTN.
3
EXTN.
4
CO 4-pin Jack
EXTN.
1
EXTN.
2
Doorphone Jack
Ground Terminal
SYSTEM
CO
CO
2
1
DPH
GROUND
Notes
• Doorphone Jack and Door Opener Connector are at SELV.
• CO Line 4-pin Jack and Extension 4-pin Jacks are at TNV.
9
Wall Mounting
1. Place the templet (on page 39) on the wall to
mark the three screw positions.
Templet
2. Install the three screws and washers (included)
into the wall.
3. Hook the main unit on the screw heads.
Opening Front Cover
1. Loosen the screw.
2. Slide the cover in the direction of the
arrow while pressing the marked
position.
SWITCHING SYSTEM
POWER
screw
Frame Ground Connection
O
DULA
R
SW
ITCHING SYSTEM
POW
ER
To Earth
IMPORTANT!!!
Connect the frame of the main unit to earth.
10
System Connection Diagram
to CO1 and CO2
2 CO Lines
Doorphone KX-T30865
Door Opener
AR
SWITCHING SYSTEM
Panasonic
Panasonic
Doorphone
6 Extensions
(two pair)
(one pair)
(two pair)
KX-T7130
Single Line Telephone
(one pair)
Panasonic
P
a
n
a
s
KX-T7050
o
n
ic
AUTO SCAN
A
N
10CH
S
PaUnasonic
C
O
T
A
H
n
ic
(two pair)
1
0
C
s
o
a
n
a
P
Cordless Phone
(one pair)
KX-T7020
Telephone Answering
Machine with Facsimile
11
CO Line Connection
Wire Specification
Connection
The wire specifications are as follows:
Wire
Solid wire
ø 0.4 – ø 0.65mm
Diameter of conductor
Diameter with coating
ø 0.66 – ø 1.05mm
Use a 4-pin plug (included) to connect CO lines.
A single plug is able to connect two CO lines. Use twisted pair cable.
1. Lift the transparent part.
2. Insert the required telephone wires into the holes of the plug.
Then press the transparent part back into the black part.
Note: Do not strip the wires.
Insert the wires all the way into the plug.
A
CO 2
B
A
CO 2
CO 1
CO 1
B
DOOR
OPENER
EXTN.
5
EXTN.
6
A
B
A
B
CO 2
CO 1
EXTN.
3
EXTN.
4
CO 2
CO 1
EXTN.
1
EXTN.
2
SYSTEM
CO
CO
2
1
DPH
GROUND
To Modular Jacks from
the Central Office
Note
• You can use cable holders to fix the wires.
12
Extension Connection
Wire Specification
Connection
The wire specifications are as follows:
Wire
Solid wire
ø 0.4 – ø 0.65 mm
Diameter of conductor
Diameter with coating
ø 0.66 – ø 1.05 mm
Use a 4-pin plug (included) to connect extension lines.
There are 6 plugs to connect extensions to EXTN. 1 through EXTN. 6
jacks.
1. Lift the transparent part.
2. Insert the required telephone wires into the holes of the plug.
Then press the transparent part back into the black part.
Note: Do not strip the wires.
Insert the wires all the way into the plug.
For a proprietary telephone
For single line telephones
H
A
B
L
A
B
DOOR
OPENER
H
A
B
L
EXTN.
1
EXTN.
5
EXTN.
6
EXTN.
3
EXTN.
4
EXTN.
1
EXTN.
2
SYSTEM
CO
CO
2
1
DPH
GROUND
To extensions
Notes
• A facsimile must be connected to EXTN.6 jack if an optional DISA/FAX Detect card (KX-
T20691) is installed. See page 16 to install the card. System programming is also required.
The “#12 Fax Connection” program should be assigned as “ENABLE”. See page 25. The
“#24 Call Incoming Mode Selection” program should be assigned as “DISA”. See page 28.
• The EXTN.1 through EXTN.6 jacks correspond to extension numbers 21 through 26 respec-
tively.
• You can use cable holders to fix the wires.
13
Paralleled Telephone Connection
Any single line telephone can be connected in parallel with a proprietary telephone.
2-conductor wiring cord
S
WITCHING SYSTEM
POW
ER
Connect pins “A” and “B”.
4-conductor wiring cord
Connect pins “H”, “A”,
“B”, and “L”.
Master
socket
Secondary
socket
Notes
• The following features are not available for SLT connected in parallel:
Call Splitting
External Feature Access
Conference
14
Installation of Optional Card and Unit
Doorphone (KX-T30865) Connection
DOOR
OPENER
A
B
DPH
EXTN.
5
EXTN.
6
EXTN.
3
EXTN.
4
EXTN.
1
EXTN.
2
SYSTEM
CO
CO
2
1
DPH
GROUND
2-conductor wiring cord
Panasonic
Panasonic
KX-T30865
Notes
• The doorphone adaptor is not required for KX-T206.
• To avoid howling, you must assign all extensions as “DISABLE” in the “#06/#76 Doorphone
Assignment (Day/Night)” program when you do not connect a doorphone.
• If howling occurs while using the doorphone feature, check the wiring.
• You can use cable holders to fix the wires.
Door Opener Connection
A user-supplied door opener can be connected to the system.
1. Loosen the screws.
2. Insert the wires coming from the door
opener into holes and tighten the screws.
DOOR
OPENER
DOOR
OPENER
EXTN.
5
EXTN.
6
EXTN.
3
EXTN.
4
EXTN.
1
EXTN.
2
To the door opener
SYSTEM
CO
CO
2
1
DPH
GROUND
3. Wind and fix the cables of the door opener
round the upper cable holder.
DOOR
OPENER
N.
EXTN.
6
XTN.
3
EXTN.
4
XTN.
1
EXTN.
2
SYSTEM
O
O
2
1
DPH
GROND
Notes
• For wiring, it is recommended to use UL1015 twisted wire or the equivalent.
• The wire should be between 1.2 and 2.4 mm in diameter including the coating.
D=1.2–2.4 mm
• Set the door opener paired with the doorphone.
15
Installation of Optional Card and Unit
DISA Card (KX-T20691) Connection
1. Disconnect the AC cord from the system. 3. Attach the DISA card to the marked connectors.
2. Loosen the screws and remove the cover.
OR
PHO
DO
NE
.
TN
6
EX
.
TN
5
EX
.
TN
4
EX
.
TN
3
EX
.
TN
2
EX
TN
1
EX
M
E
T
S
Y
S
G
IN
H
C
IT
W
S
H
DP
R
A
L
U
2
1
D
CO
O
M
IC
N
O
R
T
C
E
L
E
D
GROUN
R
E
W
O
P
4. Replace the cover and secure the screws.
5. Connect the AC cord again.
The DISA feature allows an outside caller to have direct access to intercom calls. System pro-
gramming is required. See “#10 OGM Recording” on page 24 and “#24 Call Incoming Mode
Selection” on page 28.
Keep the following conditions in mind:
• When a caller enters the second digit of an extension number (1 through 6) during the mes-
sage, he/she can reach the extension directly.
• If the call is not received, the assigned extensions will ring. See “#04/#74 CO1 Ringing
Assignment (Day/Night), “#05/#75 CO2 Ringing Assignment (Day/Night)” on page 22 and
“#60 DISA Ringing Time” on page 29.
• If the caller enters 0, the assigned extensions can receive his/her call. See “#04/#74 CO1
Ringing Assignment (Day/Night), “#05/#75 CO2 Ringing Assignment (Day/Night)” on page
22.
• If the caller enters 7, 8 or 9, or enters nothing, extension 21 will receive his/her call.
• Any calls from a rotary phone will be received by extension 21.
16
Installation of Lightning Protectors
Overview
A lightning protector is a device to be installed on a CO line to prevent a dangerous surge from
entering the building and damaging equipment.
A dangerous surge can occur if a telephone line comes in contact with a power line. Trouble due
to lightning surges have been showing a steady increase with the development of electronic
equipment.
In many countries, there are regulations requiring the installation of a lightning protector.
A lightning strike to a telephone cable which is 10 m above ground can be as high as 200,000
volts.
This system should be installed with lightning protectors.
In addition, grounding (connection to earth ground) is very important for the protection of the
system.
Installation
CO
CO
CO
Lightning
Protectors
Main
Distribution
Frame
Main Unit
EXTN
Earth Terminal
EXTN
SLT
EXTN
PT
Frame
Earth
Earth
17
Installation of Lightning Protectors
Outside
(Main Building)
Protectors
CO
(Another Building)
CO
SLT
PT
CO
Main
Main
Unit
EXTN
Distribution
Frame
Lightning
Protector
EXTN
EXTN
EXTN
TEL
TEL
Earth
Notice
If you install an extension outside of the main building, the following precautions are recom-
mended:
(1) Install the extension wire underground.
(2) Use a conduit to protect the wire.
Note
• The lightning protector for an extension is different from that for CO.
Installation of an Earth Rod
Lightning
Protector
CO
(1) Installation location of the earth rod...... Near the protector
Earth Wire
(2) Check obstructions ................................ None
(3) Composition of the earth rod ................. Metal
(4) Depth of the earth rod............................ More than 50 cm
(5) Size of the earth wire ............................. Thickness is greater
than 1.6 mm
Main
Unit
(Underground)
Earth Rod
Notes
• The above figures are recommendations only.
• The length of earth rod and the required depth depend on the
composition of the soil.
18
Power Failure Transfer
In the event of a power failure, CO2 is connected to extension 22 automatically.
Note
• The system programmed data is protected by the factory provided lithium battery.
Starting the System
Plug the AC power cord into the system and an AC outlet.
• The power indicator of the system will light.
19
General Programming Instructions
Default Setting
This system has a default factory setting. If any of the program-
ming needs to be changed, you can change the setting by system
programming.
Required Telephone Set
You can use any of the following telephones for system program-
ming:
• Proprietary Telephone (PT): KX-T7130, KX-T7020, KX-T7050
• Single Line Telephone (SLT): tone type
All telephones (except KX-T7130) do not have display panels, so
you cannot check the setting you have made. Therefore, please use
KX-T7130 to check the programming.
Extensions Used for
Programming
System programming can only be performed from extension 21.
To Check the
Programmed Data
Use KX-T7130. When you check the assignment, set the
MEMORY switch on PT to “PROGRAM”.
Enter “#” and the program address.
You cannot check programs #60, #62, #63, #65, #67, #84 and #85,
as they are not displayed on the display panel.
Before Programming
After Programming
To enter the system programming mode:
0
0
2
2
6
6
6
[Off-hook]
To exit the system programming mode:
0
2
6
6
[Off-hook]
20
System Programming
System Speed Dialling Number Set
Description
Used to program System Speed Dial numbers. These numbers are available to all exten-
sion users. There are 40 numbers from 00 through 39.
Condition
• A maximum of 32 digit numbers can be stored.
• You must store an automatic line access code (9 or 0), or an individual line code (81 or 82)
first. The automatic line access code is assigned in “#52 CO Line Access Number
Selection”.
• If you store a pause, press
.
Input Format
0
0
[AA] [Phone No.]
Explanation
• [AA]=Speed dial number: 00 through 39
• Phone number: 32 digits max.
Default
Not stored
Dial Type Selection
Description
Assigns the Dial Type (tone or pulse) to CO line.
Input Format
0
[A] [B]
1
Explanation
• [A]= 1: CO1/ 2: CO2
• [B]= 0: PULSE/ 1: TONE
Default
Both COs– 1: TONE
Outgoing Permitted CO1 Assignment (Day/Night)
Description
Determines the extensions which can have access to CO line 1 in both day and night
modes. The extension users can make outgoing CO calls if their extensions are assigned as
“ENABLE”.
Input Format
Explanation
0
7
2
2
(for day) /
(for night) [A] [B]
• [A]= 1 through 6 (corresponding to extension no. 21 through 26)
• [B]= 0: DISABLE/ 1: ENABLE
Default
All extensions– 1: ENABLE
21
System Programming
Outgoing Permitted CO2 Assignment (Day/Night)
Description
Determines the extensions which can have access to CO line 2 in both day and night
modes. The extension users can make outgoing CO calls if their extensions are assigned as
“ENABLE”.
Input Format
Explanation
(for day) /
(for night) [A] [B]
0
3
7 3
• [A]= 1 through 6 (corresponding to extension no. 21 through 26)
• [B]= 0: DISABLE/ 1: ENABLE
Default
All extensions– 1: ENABLE
CO1 Ringing Assignment (Day/Night)
Description
Assigns the extensions which will ring when a call from CO line 1 is received in both day
and modes.
Input Format
Explanation
(for day) /
(for night) [A] [B]
0
4
7 4
• [A]= 1 through 6 (corresponding to extension no. 21 through 26)
• [B]= 0: DISABLE (not ring)/ 1: ENABLE (ring)
Default
extension 21–1: ENABLE
other extensions– 0: DISABLE
CO2 Ringing Assignment (Day/Night)
Description
Assigns the extensions which will ring when a call from CO line 2 is received in both day
and modes.
Input Format
Explanation
(for day) /
(for night) [A] [B]
7 5
0
5
• [A]= 1 through 6 (corresponding to extension no. 21 through 26)
• [B]= 0: DISABLE (not ring)/ 1: ENABLE (ring)
Default
extension 21–1: ENABLE
other extensions– 0: DISABLE
22
System Programming
Doorphone Assignment (Day/Night)
Description
Assigns the extensions which will ring when a doorphone call is received and enables to
call the doorphone in both day and night modes.
Condition
• All extensions must be assigned as “0: DISABLE”, if you do not connect a doorphone to
the system.
Input Format
6
0
7
6
(for day) /
(for night) [A] [B]
Explanation
• [A]= 1 through 6 (corresponding to extension no. 21 through 26)
• [B]= 0: DISABLE/ 1: ENABLE
Default
extension 21–1: ENABLE
other extensions– 0: DISABLE
Toll Restriction (TRS) – Class Assignment (Day/Night)
Description
Assigns a Toll Restriction Class to each extension in both day and night modes. The Toll
Restriction feature can prohibit certain extension users from placing unauthorized toll calls.
The following four classes are available:
Class
Restricted calls
CLASS 1
CLASS 2
CLASS 3
None
Numbers programmed in “#08 Denied code (Class 2, 3) ”
Numbers programmed in “#08 Denied code (Class 2, 3)
and “#09 Denied code (Class 3)”
CLASS 4
All CO calls
Condition
• Emergency call numbers “112” and “999” are excepted from toll restriction.
Input Format
(for day) /
(for night) [A] [B]
0
7
7
7
Explanation
• [A]= 1 through 6 (corresponding to extension no. 21 through 26)
• [B]= 1: CLASS 1/ 2: CLASS 2/ 3: CLASS 3/ 4: CLASS 4
Default
All extensions– 1: CLASS 1
23
System Programming
TRS Denied Code (CLASS 2, 3)
Description
Allows you to specify the numbers which are toll-restricted for TRS Class 2 and Class 3.
Condition
• The character “ ” can be any number.
Input Format
0 8
[A] [Denied code No.]
Explanation
• [A]= Code No.: 0 through 9 1 digit
• Denied code number: 7 digits,
Default
All codes– Not stored
TRS Denied Code (CLASS 3)
Description
Allows you to specify the numbers which are toll-restricted for TRS Class 3.
Condition
• The character “ ” can be any number.
Input Format
[A] [Denied code No.]
0
9
Explanation
• [A]= Code No.: 0 through 9 1 digit
• Denied code number: 7 digits,
Default
All codes– Not stored
OGM Recording
Description
Used to record an outgoing message for Direct Inward System Access (DISA).
Condition
• The recording time is a maximum of 16 seconds.
• If you perform programming with a PT, the message “RECORDING” will be displayed on
its panel.
• If the DISA/FAX Detect card is not installed, you will hear a reorder tone and the program
is finished.
Message example: “This is AAA company. Please enter 1 for Mr. AA, 2 for Mr. BB .......
6 for Ms. FF. Thank you.”
Input Format
0
1
(Record your message)
24
System Programming
OGM Play
Description
Confirms the outgoing message recorded in the OGM Recording program.
Condition
• If you perform programming with a PT, the message “PLAYBACK” will be displayed on
its panel.
Input Format
1 1
Fax Connection
Description
Allows the system to detect the CNG tone from a facsimile. If it is set to “ENABLE”,
extension 26 will receive fax transmission data.
Condition
• The optional DISA/FAX Detect card (KX-T20691) should be installed.
• The “#24 Call Incoming Mode Selection” program should be assigned as “DISA”.
• Extension 26 should be assigned as “DISABLE” in the “#04/#74 CO1 Ringing Assignment
(Day/Night)”, “#05/#75 CO2 Ringing Assignment (Day/Night)” and “#06/#76 Doorphone
Assignment (Day/Night)” programs.
Input Format
[A]
1 2
Explanation
• [A]= 0: DISABLE (not detect)/ 1: ENABLE (detect)
Default
0: DISABLE
CO1 Delayed Ringing Assignment
Description
Assigns delayed ringing to extensions when a call from CO line 1 is received.
Condition
• The number of delayed rings is assigned by the “#15 Delayed Ringing Count Selection”
program.
• This feature is not available for the calls sent by the DISA feature.
Input Format
1
3
[A] [B]
Explanation
• [A]= 1 through 6 (corresponding to extension no. 21 through 26)
• [B]= 0: DISABLE (not delayed)/ 1: ENABLE (delayed)
Default
All extensions– 0: DISABLE
25
System Programming
CO2 Delayed Ringing Assignment
Description
Assigns delayed ringing to extensions when a call from CO line 2 is received.
Condition
• The number of delayed rings is assigned by the “#15 Delayed Ringing Count Selection”
program.
• This feature is not available for the calls sent by the DISA feature.
Input Format
[A] [B]
1
4
Explanation
• [A]= 1 through 6 (corresponding to extension no. 21 through 26)
• [B]= 0: DISABLE (not delayed)/ 1: ENABLE (delayed)
Default
All extensions– 0: DISABLE
Delayed Ringing Count Selection
Description
Assigns the number of delayed rings that will be sent to the assigned extensions from the
CO lines.
Input Format
Explanation
1
5
[A]
• [A]= 1: After 1 ring/ 2: After 2 rings/ 3: After 3 rings/ 4: After 4 rings
2: After 2 rings
Default
TRS Excepted Code
Description
Assigns the numbers which are exceptions to the toll restriction. You can store a maximum
of 30 codes.
Condition
• The character “ ” can be any number.
Input Format
1
6
[A] [Excepted code No.]
Explanation
• [A]= Code No.: 00 through 29 2 digits
• Excepted code number: 7 digits,
Default
All codes– Not stored
26
System Programming
Door Opener Assignment
Description
Assigns each extension to have access to door opener or not.
Input Format
6 1 [A] [B]
Explanation
• [A]= 1 through 6 (corresponding to extension no. 21 through 26)
• [B]= 0: DISABLE/ 1: ENABLE
Default
All extensions– 1: ENABLE
Day/Night Switching Mode
Description
Assigns automatic or manual day/night mode.
Condition
• If automatic switching mode is assigned, day/night mode is switched at the time
programmed in “#71 Day/Night Starting Time”.
Input Format
0
7
[A]
Explanation
• [A]= 0: Manual/ 1: Automatic
Default
0: Manual
Day/Night Starting Time
Description
Sets the starting time when automatic day/night mode is programmed in the “#70 Day/
Night Switching Mode” program.
Input Format
Explanation
[A] [BB] [CC] [D]
7
1
• [A]= 1: Day start time / 2: Night start time
• [CC]=Minute: 00-59
• [BB]= Hour: 01-12
• [D]=0: AM / 1: PM
Default
Day– 9:00 AM
Night–5:30 PM
System Data Clear
Description
Allows the system to re-initialize the system-programmed data. The features mentioned in
“Station Feature Clear” are also re-initialized. See page 11 of the User Manual. When all
the programmed data is cleared, the system will restart with the default setting.
Input Format
9
9
27
System Programming
Other Programs
• Host PBX Access Code Assignment
Assigns a Host PBX access code to make an
outside call, if the system is installed behind the
host PBX. A pause is automatically inserted
after the access code and the toll restriction
feature applies to the number after the code.
Input Format: #21 [A] [code] #
• Tone Waiting Time After OGM
Sets the time between sending an outgoing
message and sending the ringback tone.
Input Format: #40 [A]
• [A]=0: 0 SEC/ 1: 5 SEC (default)/ 2: 10 SEC/
3: 15 SEC
• Hold Recall Time
• [A]=1: CO1/ 2: CO2
• [code] = 2 digits max. (Default : Not stored)
Assigns the length of the hold recall timer and
transfer recall timer. The hold recall timer is
used to alert an extension that a call has been
held for an extended period of time. The
transfer recall timer is used to alert an extension
that a transferred call has not been answered for
an extended period of time.
• Hookswitch Flash Time Assignment
Sets the time to send the flash signal to each CO
line.
Input Format: #22 [A] [B]
• [A]=1: CO1/ 2: CO2
• [B]=0: 80 ms/ 1: 100 ms (default)/ 2: 160 ms/
3: 300 ms/ 4: 600 ms / 5: 900 ms /
6: 1200 ms
Input Format: #50 [A]
• [A]=0: 30 SEC (default)/ 1: 1 MIN / 2: 2 MIN/
3: 3 MIN/ 4: 4 MIN/ 5: DISABLE
• CO Pulse Selection
• Hold Mode Selection for SLT
Assigns the method to put a call on hold with
SLTs.
Input Format: #51 [A]
• [A]=1: MODE 1 (hooking) (default)
2: MODE 2 (hooking and dial 6)
Assigns to send the pulse to CO line during a
conversation with an outside party when the “#01
Dial Type Selection” program is assigned as
“Pulse”.
Input Format: #23 [A]
• [A]=0: DISABLE/ 1: ENABLE (default)
• CO Line Access Number Selection
Selects the automatic line access number.
Input Format: #52 [A]
• Call Incoming Mode Selection
Assigns whether to use the DISA feature or not.
This program is available when the DISA/FAX
Detect card is installed.
• [A]=1: 9 (default)/ 2: 0
Input Format: #24 [A] [B]
• [A]=1: CO1/ 2: CO2
• [B]=0: NORMAL (default)/ 1: DISA
• Conference Tone
Assigns whether or not to delete the conference
tone. You hear the tone when the conference or
the executive busy override feature begins and
finishes.
Input Format: #53 [A]
• [A]=0: DISABLE/ 1: ENABLE (default)
• Bell Off Detection
Sets the time between one bell signal detection
and the next signal from a Central Office.
Input Format: #25 [A]
• [A]=1: 6 SEC/ 2: 3 SEC (default)
• Music on Hold Use
Selects whether or not to use internal music as
the music on hold.
Input Format: #54 [A]
• [A]=1: MODE 1 (NO MUSIC) (default)/
2: MODE 2 (MUSIC)
• Intercom Alerting Assignment
Assigns the intercom alerting mode to each
extension when an intercom call reaches.
Input Format: #30 [A] [B]
• [A]=1 through 6 (corresponding to extension
no. 21 through 26)
• [B]=0: TONE (default)/ 1: VOICE
• Paralleled Telephone Connection
Assigns whether each extension will be con-
nected in parallel with a single line telephone or
not.
Input Format: #31 [A] [B]
• [A]=1 through 6 (corresponding to extension
no. 21 through 26)
• [B]=0: DISABLE (default)/ 1: ENABLE
28
System Programming
Other Programs (continued)
• DISA Ringing Time Assignment
Sets the time to forward a call sent by the DISA
feature to other extensions. If the call is not
answered by the designated extension within the
programmed time, the call is forwarded to
extensions which are not assigned as “DIS-
ABLE” in the #04/#74 CO1 Ringing Assignment
(Day/Night) and #05/#75 CO2 Ringing Assign-
ment (Day/Night). If “DISABLE” is selected in
this program, the telephone at the designated
extension rings for 60 seconds and the call is not
forwarded.
• Hookswitch Flash Time Range
Assignment
Sets the hookswitch flash time range.
Input Format: #65 [A]
• [A]=1: 80–1000ms / 2: 80–150ms
3: 50–150ms (default)
• Door Opener Access Time
Assigns the length of the Door Opener time.
The door is unlocked for the assigned time.
Input Format: #67 [A]
• [A]= 1: 1 sec/ 2: 2 sec/ 3: 3 sec/ 4: 4 sec/
5: 5 sec (default) / 6: 6 sec/ 7: 7 sec /
8: 8 sec
Input Format: #60 [A]
• [A]=0: DISABLE / 1: 10 SEC/
2: 20 SEC (default)/ 3: 35 SEC
• Toll Restriction Code Check
Assigns whether “ ” or “#” is to be checked or
not when a user dials them in the Toll Restriction
code.
Input Format: #62 [A]
• [A]=0: DISABLE/ 1: ENABLE (default)
• CO Indicator Assignment
Assigns whether an incoming CO call indicates
or not on the CO button. Also it allows an
extension user to answer the call by pressing the
CO button when “DISABLE” is selected in the
#04/#74 “CO1 Ringing Assignment” or the #05/
#75 “CO2 Ringing Assignment” program.
Input Format: #63 [A]
• [A]=0: DISABLE (The indicator lights red and
a user cannot answer the
call.)
1: ENABLE (The indicator is flashing and
a user can answer the call.)
(default)
Note
• You cannot check the assignments of the programs, #60, #62, #63, #65 and #67 by setting the
MEMORY switch to “PROGRAM”, and entering “#” and the program address.
29
System Programming
Least Cost Routing (LCR) Programs
Least Cost Routing (LCR) is a system programmable feature that automatically selects the least
expensive route available at the time a long distance call is made.
It is not necessary to dial the access code of the least expensive carrier.
You must assign the programs on the next page to activate the LCR feature.
The following chart shows the procedure of LCR feature.
LCR Sequence chart
Yes
Yes
Is the dialled number an
emergency call number?
No
Is the dialled number a
BLT access code?
No
No
Does the first digit match
the leading digit?
Yes
BTL is selected.
Yes
Yes
Yes
Yes
No
No
No
No
Does the area code match the
route selection code of Route 1?
Does the area code match
the exceptional code of Route 1?
No
Yes
Route 1 is selected.
Does the area code match the
route selection code of Route 2?
Does the area code match
the exceptional code of Route 2?
No
Yes
Route 2 is selected.
Does the area code match the
route selection code of Route 3?
Does the area code match
the exceptional code of Route 3?
No
Yes
Route 3 is selected.
Route 4 is selected.
Does the area code match
the exceptional code of Route 4?
Does the area code match the
route selection code of Route 4?
No
Yes
BLT is selected.
30
System Programming
Least Cost Routing (LCR) Programs (continued)
• LCR Mode
• LCR Itemized Bill Code
Allows you to turn on or off the Least Cost
Routing (LCR) mode. LCR, if enabled, selects
the least expensive route to be used for a CO call.
Input Format: #80 [A] [B]
Assigns whether to register the itemized bill
code (extension number 21 through 26) to each
CO line or not. This code is used for dividing a
bill to a CO line.
• [A]=1: CO1/ 2: CO2
• [B]=0: DISABLE (default)/ 1: ENABLE
Input Format: #86 [A] [B]
• [A]=1: CO1/ 2: CO2
• [B]=0: DISABLE (default)/ 1: ENABLE
• LCR Carrier Code
Assigns each carrier's access code used for the
LCR feature.
Input Format: #81 [A] [code] #
• [A]=Route No.: 1 through 4
• [code] =10 digits max.
• BTL Access Code
Stores the BTL (British Telecom Line) access
code. When this code is dialled, the BTL is
always selected even if the LCR feature is
enabled.
(Default : all routes – 131)
Input Format: #87 [code] #
• [code]=4 digits max. (default: 121)
• LCR Modify Mode
• LCR Route Exceptional Code
Assigns dialling numbers that are excepted from
LCR routing plans of the specified carrier. You
can store a maximum of 20 codes for each
route.
Assigns whether to change the numbers after the
carrier code to the TONE mode or not when “#01
Dial Type Selection” program is assigned as
“Pulse”.
Input Format: #82 [A] [B]
• [A]=Route No.: 1 through 4
Input Format: #88 [A] [B] [code] #
• [A]=Route No.: 1 through 4
• [B]=0: PULSE/1: TONE (default)
• [B]=Area code No.: 00 through 19
• [code]= 6 digits max.
(Default: all routes – not stored)
• LCR Route Selection Code
Assigns area codes (except the leading digit)
which is selected by the LCR feature for each
route. You can store a maximum of 40 codes for
each route.
Input Format: #83 [A] [BB] [code] #
• [A]= Route No.: 1 through 4
• [BB]= Code No.: 00 through 39
• [code]=6 digits max.
• LCR Leading Digit Entry
Registers Leading digits of an area code to
judge whether to select a route for the LCR
feature. When the first digit of the dialled
number matches with the registered number, it
is considered a long distance call and proceeds
to the LCR procedure.
(Default: Not stored)
Input Format: #89 [code] #
• [code]=2 digits max. (default: 0)
• LCR Password Set
Assigns a password to register an authorization
code. The password is not displayed on the
display panel during setting.
Input Format: #84 [old password] [new password]
• [Password]=4 digits max. (default: 1234)
Conditions
• To clear the LCR route selection code, press
#83 [A] [BB] #
• To clear the LCR authorization code, press
#85 [password] [A] [B] #
• To clear the BTL access code, press #87#.
• To clear the LCR route exceptional code, press
#88 [A] [B] #
• LCR Authorization Code Set
Registers an authorization code applied to each
CO line and each route. The authorization codes
are not displayed on the display panel during
setting.
Input Format: #85 [password] [A] [B] [code]
• [password]=enter the password set by # 84
program
• [A]=Route No.: 1 through 4
• [B]=1: CO1/ 2: CO2
• [code]=20 digits max.
(Default: both CO lines, all routes – not stored)
31
Tone / Ring Tone
<Tone>
1 sec
Confirmation Tone 1
Confirmation Tone 2
Confirmation Tone 3
(Conference Tone)
Dial Tone 1
Dial Tone 2
Busy Tone
Reorder Tone
Ringback Tone
Do Not Disturb (DND)
Tone
15 sec
Hold Alarm
Call Waiting Tone
32
Tone / Ring Tone
<Ring Tone>
1 sec
Intercom Calls /
Intercom Hold Recall
CO Calls /
CO Hold Recall
Doorphone Calls
NOTE
• The dial tone 2 is heard during the system programming mode and when the following
features are set:
Do Not Disturb
Call Pickup Deny
Call Forwarding
Data Line Security
33
Programming Tables
[#00] System Speed Dialling Number Set
Phone No. (32 digits max.)
Name
No.
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
34
Programming Tables
[#01] Dial Type Selection
[#12] Fax Connection
Default CO1 CO2
0: PULSE
Selection
Default
✓
0: DISABLE
1: ENABLE
1: TONE
✓
[
#02] Outgoing Permitted CO 1 Assignment (Day)
[
#72] Outgoing Permitted CO 1 Assignment (Night)
Default Ext.21 Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
Default Ext.21 Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
0: DISABLE
1: ENABLE
0: DISABLE
1: ENABLE
✓
✓
[#03] Outgoing Permitted CO 2 Assignment (Day)
[#73] Outgoing Permitted CO 2 Assignment (Night)
Default Ext.21 Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
0: DISABLE
Default Ext.21 Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
0: DISABLE
1: ENABLE
1: ENABLE
✓
✓
[#04] CO 1 Ringing Assignment (Day)
[#74] CO 1 Ringing Assignment (Night)
Default Ext.21 Default Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
Default Ext.21 Default Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
0: DISABLE
1: ENABLE
0: DISABLE
1: ENABLE
✓
✓
✓
✓
[#05] CO 2 Ringing Assignment (Day)
[#75] CO 2 Ringing Assignment (Night)
Default Ext.21 Default Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
Default Ext.21 Default Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
0: DISABLE
1: ENABLE
0: DISABLE
1: ENABLE
✓
✓
✓
✓
[#06] Doorphone Assignment (Day)
[#76] Doorphone Assignment (Night)
Default Ext.21 Default Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
Default Ext.21 Default Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
0: DISABLE
1: ENABLE
0: DISABLE
1: ENABLE
✓
✓
✓
✓
[#07] Toll Restriction (TRS) – Class Assignment (Day) [#77] Toll Restriction (TRS) – Class Assignment (Night)
Default Ext.21 Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
✓
Default Ext.21 Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
✓
1: CLASS 1
2: CLASS 2
3: CLASS 3
4: CLASS 4
1: CLASS 1
2: CLASS 2
3: CLASS 3
4: CLASS 4
[#08] TRS Denied Code [#09] TRS Denied Code
[#13] CO 1 Delayed Ringing Assignment
(CLASS 2, 3)
(CLASS 3)
Default Ext.21 Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
0: DISABLE
1: ENABLE
✓
Code Number (7 digits)
Code Number (7 digits)
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
[#14] CO 2 Delayed Ringing Assignment
Default Ext.21 Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
✓
0: DISABLE
1: ENABLE
[#15] Delayed Ringing Count Selection
Selection
Default
1: 1 RING
2: 2 RINGS
3: 3 RINGS
4: 4 RINGS
✓
[#16] TRS Excepted Code
Code Number (7 digits) Code Number (7 digits) Code Number (7 digits) Code Number (7 digits) Code Number (7 digits) Code Number (7 digits)
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
35
Programming Tables
[#61] Door Opener Assignment
Default Ext.21 Ext.22 Ext.23 Ext.24 Ext.25 Ext.26
0: DISABLE
1: ENABLE
✓
[#70] Day/Night Switching Mode
[#71] Day/Night Starting Time
Selection
Default Selection
9:00AM
2: NIGHT 5:30PM
Default
✓
0: MANUAL
1: AUTO
1: DAY
[#83] LCR Route Selection Code
Route 1
Route 2
Route 3
Route 4
No. Code (6 digits max.) No. Code (6 digits max.) No. Code (6 digits max.) No. Code (6 digits max.)
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
36
Programming Tables
[#88] LCR Route Exceptional Code
Route 1
Route 2
Route 3
Route 4
No. Code (6 digits max.) No. Code (6 digits max.) No. Code (6 digits max.) No. Code (6 digits max.)
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
37
Templet
Up
71 mm
77 mm
Install a screw here
Install a screw here
Install a screw here
• Copy the templet and place it on the wall.
39
Panasonic Business Systems U.K.
Panasonic House, Willoughby Road, Bracknell,
Berkshire RG12 4FP
Printed in Japan
PSQX1141ZB KW0397KM1097
|